In a steam engine, the cylinder is connected to the condenser by

In a steam engine, the cylinder is connected to the condenser by
by

1 Answer

Answer :

outlet valve.
by

Related questions

The pressure of steam in the engine cylinder at the beginning of the stroke is ________ the boiler pressure. (A) Equal to (B) Less than (C) Higher than (D) None of these

Description : The pressure of steam in the engine cylinder at the beginning of the stroke is ________ the boiler pressure. (A) Equal to (B) Less than (C) Higher than (D) None of these

Last Answer : (B) Less than

The valve rod connected in steam engine by using.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Description : The valve rod connected in steam engine by using.. A. Cotter joint B. Knuckle joint C. Universal coupling D. Bolted joint

Last Answer : B. Knuckle joint

In steam engine, the piston rod is usually connected to the cross head by means of a....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Description : In steam engine, the piston rod is usually connected to the cross head by means of a....... A. Cotter joints B. Universal joints C. Knuckle joint D. Bearing

Last Answer : A. Cotter joints

In most of the vacuum crystalliser, vacuum is generally produced by means of a (A) Suction pump (B) Compressed air jet (C) Steam jet ejector with a barometric condenser (D) None of these

Description : In most of the vacuum crystalliser, vacuum is generally produced by means of a (A) Suction pump (B) Compressed air jet (C) Steam jet ejector with a barometric condenser (D) None of these

Last Answer : (C) Steam jet ejector with a barometric condenser

Small scale evaporation is done in a (A) Heat exchanger (B) Condenser(C) Multiple effect evaporator(D) Steam jacketed kettle

Description : Small scale evaporation is done in a (A) Heat exchanger (B) Condenser (C) Multiple effect evaporator (D) Steam jacketed kettle

Last Answer : (D) Steam jacketed kettle

In a Rankine cycle, with the maximum steam temperature being fixed from metallurgical considerations, as the boiler pressure increases (a) The condenser load will increase [IES-1997] (b) The quality of turbine exhaust will decrease (c) The quality of turbine exhaust will increase (d) The quality of turbine exhaust will remain unchanged

Description : In a Rankine cycle, with the maximum steam temperature being fixed from metallurgical considerations, as the boiler pressure increases (a) The condenser load will increase [IES-1997] (b) The ... The quality of turbine exhaust will increase (d) The quality of turbine exhaust will remain unchanged

Last Answer : (b) The quality of turbine exhaust will decrease 

The efficiency of superheat Rankine cycle is higher than that of simple Rankine cycle because [GATE-2002] (a) The enthalpy of main steam is higher for superheat cycle (b) The mean temperature of heat addition is higher for superheat cycle (c) The temperature of steam in the condenser is high (d) The quality of stem in the condenser is low

Description : The efficiency of superheat Rankine cycle is higher than that of simple Rankine cycle because [GATE-2002] (a) The enthalpy of main steam is higher for superheat cycle (b) The mean temperature of heat ... temperature of steam in the condenser is high (d) The quality of stem in the condenser is low 

Last Answer :  (b) The mean temperature of heat addition is higher for superheat cycle  

Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively. (A) 70 & 30 (B) 30 & 70 (C) 50 & 50 (D) 90 & 10

Description : Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively. (A) 70 & 30 (B) 30 & 70 (C) 50 & 50 (D) 90 & 10

Last Answer : (A) 70 & 30

Pressure of steam in condenser is (A) Atmospheric pressure (B) More than atmospheric pressure (C) Slightly less than atmospheric pressure (D) much less than atmospheric pressure.

Description : Pressure of steam in condenser is (A) Atmospheric pressure (B) More than atmospheric pressure (C) Slightly less than atmospheric pressure (D) much less than atmospheric pressure.

Last Answer : much less than atmospheric pressure.

In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Description : In a steam condenser, the partial pressure of steam and air are 0.06 bar and 0.007 bar respectively. The condenser pressure is (A) 0.007 bar (B) 0.053 bar (C) 0.06 bar (D) 0.067 bar

Last Answer : (D) 0.067 bar

A boiler is an enclosed vessel that provides a means for ________ and ______ heat to water until it becomes hot water or steam. a. Generate, boiler b. Condenser, loop c. Combustion, transfers d. All of above

Description : A boiler is an enclosed vessel that provides a means for ________ and ______ heat to water until it becomes hot water or steam. a. Generate, boiler b. Condenser, loop c. Combustion, transfers d. All of above

Last Answer : c. Combustion, transfers

What is the main component in a boiler a) steam b) heat c) pressure condenser d) combination

Description : What is the main component in a boiler a) steam b) heat c) pressure condenser d) combination

Last Answer : a) steam

How many types of steam condenser are known?

Description : How many types of steam condenser are known?

Last Answer : 1. Jet Condensers - direct contact heat exchanger. 2. Surface Condensers - indirect contact heat exchanger using water. 3. Air Condensers - direct contact heat exchangers using air.

Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Description : Describe any two sources of air leak in surface condenser. Also describe effect of air leak on latent heat of steam and cooling water requirements.

Last Answer : ✓ The main sources of air leakage found in condenser are given below: 1) There is leakage of air from atmosphere at the joint of the parts which are internally under a pressure less ... hence evaporation enthalpy of steam increases therefore more amount of cooling water required in the condenser. 

Describe the construction and working of two pass flow surface condenser also write it’s function and location in steam power plant.

Description : Describe the construction and working of two pass flow surface condenser also write it’s function and location in steam power plant.

Last Answer : Construction: It consists of horizontal cast iron cylindrical vessel pack with tubes, through which the cooling water flows. The ends of the condenser are cut off by vertical perforated type plates ... hot feed water to boiler. Location in steam power plant- between turbine and feed pump 

(i) Draw the neat sketch of bomb calorimeter. (ii) Write any three sources of air leakage in steam condenser.

Description : (i) Draw the neat sketch of bomb calorimeter. (ii) Write any three sources of air leakage in steam condenser.

Last Answer : (i)   (ii) Sources of air leakage in condenser: i) Air leak through joints and packing. ii) Air also comes in condenser with the steam. iii) In jet condensers dissolved air in the cooling water enters the condenser. 

Explain the application of second law of thermodynamics to refrigerator. State any three functions of steam condenser.

Description : Explain the application of second law of thermodynamics to refrigerator. State any three functions of steam condenser. 

Last Answer : According to Clausius s statement heat cannot flow itself from cold body to a hot body without help of external agency REFERIGERATOR is shown in the figure with cold body (T2) and hot body ( ... well from where it is pumped back to the boiler. 3) To remove of air and non-condensable gases

For steam power plant having capacity 600 MW capacity a cooling tower is required to set up with condenser. Suggest the type of condenser and cooling tower with justification.

Description : For steam power plant having capacity 600 MW capacity a cooling tower is required to set up with condenser. Suggest the type of condenser and cooling tower with justification. 

Last Answer : For Steam power plant having Capacity 600 MW the requirement of condenser and cooling tower is as follow. 1) Condenser:- Given Capacity is medium to low capacity for this we can use Jet Condenser ... and efficiency of tower is high  -Temperature of water coming out from tower can be controlled.

Which of the following thermodynamic devices operates the reverse of the heat engine?  a. Thermal pump  b. Thermal evaporator  c. Thermal condenser  d. Thermal equilibrant

Description : Which of the following thermodynamic devices operates the reverse of the heat engine?  a. Thermal pump  b. Thermal evaporator  c. Thermal condenser  d. Thermal equilibrant

Last Answer : Thermal pump

Can you put a 1999 gmc sonoma 4 cylinder engine with automatic transmission in a 1994 gmc sonoma 4 cylinder engine that has a 5 speed transmission?

Description : Can you put a 1999 gmc sonoma 4 cylinder engine with automatic transmission in a 1994 gmc sonoma 4 cylinder engine that has a 5 speed transmission?

Last Answer : UPDATE......We just went a totally different way with it... No need for anyone trying to answer.Thank you all

What is the speed of the piston in the cylinder of a petrol engine ?

Description : What is the speed of the piston in the cylinder of a petrol engine ?

Last Answer : The speed of the piston in the cylinder of a petrol engine is also the speed of the alternator.

What is the tightening of cylinder head bolt on KIA NAZA RIA 2.5L GASOLINE ENGINE?

Description : What is the tightening of cylinder head bolt on KIA NAZA RIA 2.5L GASOLINE ENGINE?

Last Answer : Need answer

How many horsepower will a 3 cylinder engine deliver?

Description : How many horsepower will a 3 cylinder engine deliver?

Last Answer : Well, based on my research, the average Horsepower delivered from a 3 cylinder engine is around 180 to 200, on average. It would also depend on the car it is going into and furthermore, with ... means increased cylinders to make up the difference to be able to move a car and distribute the force.

Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley

Description : Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley

Last Answer : ANSWER : C

Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine

Description : Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine

Last Answer : ANSWER : D

Which of the following is compressed in a diesel engine cylinder A. air B. fuel C. air and fuel D. air and lub oil

Description : Which of the following is compressed in a diesel engine cylinder A. air B. fuel C. air and fuel D. air and lub oil

Last Answer : ANSWER : A

If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Description : If one cylinder of a diesel engine receives more fuel than others , then for that cylinder the A. exhaust will be smoky B. scavenging occurs C. exhaust temperature will be high D. engine starts overheating

Last Answer : ANSWER : B

An engine indicator is used to determine the following A. Speed B. Temperature C. M.E.P D. Volume of cylinder

Description : An engine indicator is used to determine the following A. Speed B. Temperature C. M.E.P D. Volume of cylinder

Last Answer : ANSWER : C

In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Description : In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Last Answer : In two stroke engine there is one power stroke in _____ of crankshaft rotation. a. 90° b. 180° c. 270° d. 360° (Ans:d)

In _____________ injection system only one pump is sufficient for multi-cylinder engine. a) air b) mechanical c) compression fuel d) common rail

Description : In _____________ injection system only one pump is sufficient for multi-cylinder engine. a) air b) mechanical c) compression fuel d) common rail

Last Answer : Answer: d Explanation: None.

If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Last Answer : Ans :c

In a morse test for a 2 cylinder, 2 S SI engine, the brake power was 9 kW. Whereas the brake power of individual cylinders with spark cut off were 4.25 kW and 3.75 kW. The mecheffic of the engine is (a) 90% (b) 80% (c) 45.5% (d) 52.5%

Description : In a morse test for a 2 cylinder, 2 S SI engine, the brake power was 9 kW. Whereas the brake power of individual cylinders with spark cut off were 4.25 kW and 3.75 kW. The mecheffic of the engine is (a) 90% (b) 80% (c) 45.5% (d) 52.5%

Last Answer : Ans :a

A two stroke engine has a speed of 750 rpm. A four stroke engine having an identical cylinder size runs at 1500 rpm. The theoretical output of the two stroke engine will (a) Be twice that of the four stroke engine (b) Be half that of the four stroke engine (c) Be the same as that of the four stoke (d) Depend upon whether it is a CI or SI engine

Description : A two stroke engine has a speed of 750 rpm. A four stroke engine having an identical cylinder size runs at 1500 rpm. The theoretical output of the two stroke engine will (a) Be twice that of the four stroke ... ) Be the same as that of the four stoke (d) Depend upon whether it is a CI or SI engine

Last Answer : Ans :c

The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test

Description : The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test

Last Answer : Ans : a

An engine indicator is used to determine the following a. Speed. b. Temperature. c. Volume of cylinder. d. Mean effective pressure and Indicated horse power.

Description : An engine indicator is used to determine the following a. Speed. b. Temperature. c. Volume of cylinder. d. Mean effective pressure and Indicated horse power.

Last Answer : ANSWER d. Mean effective pressure and Indicated horse power.

Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold

Description : Mixing of air and fuel in the diesel engine occurs in a. injection pump b. carburetor c. engine cylinder d. inlet manifold

Last Answer : ANSWER c. engine cylinder

The most popular firing order in a 4-cylinder inline internal combustion engine is a. 1-2-3-4 b. 1-3-2-4 c. 1-3-4-2 d. 1-2-4-3

Description : The most popular firing order in a 4-cylinder inline internal combustion engine is a. 1-2-3-4 b. 1-3-2-4 c. 1-3-4-2 d. 1-2-4-3

Last Answer : ANSWER b. 1-3-4-2

In a 75 cc engine the parameter cc indicates a. fuel tank capacity b. lubricating oil capacity c. swept volume d. cylinder volume

Description : In a 75 cc engine the parameter cc indicates a. fuel tank capacity b. lubricating oil capacity c. swept volume d. cylinder volume

Last Answer : ANSWER c. swept volume

Which of the following medium is compressed in a diesel engine cylinder? a. air b. air and fuel c. air and lubricating oil d. fuel

Description : Which of the following medium is compressed in a diesel engine cylinder? a. air b. air and fuel c. air and lubricating oil d. fuel

Last Answer : ANSWER a. air

The maximum temperature in the I.C engine cylinder is of the order of a. 500 – 1000 C b. 1000 – 1500 C c. 1500 – 2000 C d. 2000 – 2500 C

Description : The maximum temperature in the I.C engine cylinder is of the order of a. 500 – 1000 C b. 1000 – 1500 C c. 1500 – 2000 C d. 2000 – 2500 C

Last Answer : ANSWER d. 2000 – 2500 C

An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per cycle is 1800 kJ/kg, then work output per cycle per kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Description : An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per ... kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Last Answer : ANSWER d. 973.5 kJ

Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Description : Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Last Answer : ANSWER d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

The firing order of four stroke four cylinder engine is a. 1-2-3-4 b. 1-3-2-4 c. 1-3-4-2 d. 1-4-3-2

Description : The firing order of four stroke four cylinder engine is a. 1-2-3-4 b. 1-3-2-4 c. 1-3-4-2 d. 1-4-3-2

Last Answer : c. 1-3-4-2

Which of the following types of internal combustion engine is generally used as portable engine for pumping and electricity generation? 1. Spark ignition 2. Stationary 3. Vertical single cylinder 3. all of these

Description : Which of the following types of internal combustion engine is generally used as portable engine for pumping and electricity generation? 1. Spark ignition 2. Stationary 3. Vertical single cylinder 3. all of these

Last Answer : ans 2

Piston-cylinder arrangement of an internal combustion engine in automobile is called _________.  1. Rotary Joints  2. Prismatic Joints  3. Revolute Joints  4. Spherical Joints

Description : Piston-cylinder arrangement of an internal combustion engine in automobile is called _________.  1. Rotary Joints  2. Prismatic Joints  3. Revolute Joints  4. Spherical Joints

Last Answer : 2

The EGT indication on a piston engine is used: a. To control the cooling air shutters b. To monitor the oil temperature c. To assist the pilot to adjust the fuel mixture d. To indicate cylinder head temperature

Description : The EGT indication on a piston engine is used: a. To control the cooling air shutters b. To monitor the oil temperature c. To assist the pilot to adjust the fuel mixture d. To indicate cylinder head temperature

Last Answer : c. To assist the pilot to adjust the fuel mixture

The EGT indication on a piston engine is used: a. To control the cooling air shutters b. To monitor the oil temperature c. To assist the pilot to adjust the fuel mixture d. To indicate cylinder head temperature

Description : The EGT indication on a piston engine is used: a. To control the cooling air shutters b. To monitor the oil temperature c. To assist the pilot to adjust the fuel mixture d. To indicate cylinder head temperature

Last Answer : c. To assist the pilot to adjust the fuel mixture

.When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Description : .When the valves are carried in engine bioel at one side of each cylinder is called A. Valves in head arrangements B. L-head C. I-head D. None of the above

Last Answer : B. L-head

An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Description : An engine is called I or valve in head engine when a) Valve are immediately above the cylinder b) Both valves are on one side c) Both valves are on opposite direction d) None of the above

Last Answer : d) None of the above

iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Description : iesel engine has less reserve torque then spark ignition because ∙ Torque-speed curve is governed by volumetric efficiency of fuel pump and engine cylinder ∙ Torque is a function of thermal efficiency ∙ Diesel engine has generally low speed engine ∙ None of the above

Last Answer : ∙ Torque is a function of thermal efficiency