Description : Drying of refractory is normally carried out in a __________ dryer. (A) Open pan (B) Tray (C) Rotary vacuum (D) Truck/tunnel
Last Answer : (D) Truck/tunnel
Description : Calcium ammonium nitrate (a fertiliser) is dried in a __________ dryer. (A) Rotary (B) Vacuum (C) Tunnel (D) Tray
Last Answer : (A) Rotary
Description : Large scale drying of sugar is done in a __________ dryer. (A) Spouted bed (B) Tray (C) Rotary (D) Truck
Last Answer : (C) Rotary
Description : Large scale drying of wheat is done in a __________ dryer. (A) Fluidised bed (B) Spouted bed (C) Tray (D) Vacuum rotary
Last Answer : (B) Spouted bed
Description : Sticky material can be dried in a __________ dryer. (A) Tray (B) Rotary (C) Fluidised bed (D) None of these
Last Answer : (A) Tray
Description : Refractory bricks are usually dried in a __________ dryer. (A) Tray (B) Tunnel (C) Conveyor (D) Festoon
Last Answer : (B) Tunnel
Description : Milk is dried usually in a __________ dryer. (A) Freeze (B) Spray (C) Tray (D) Rotary
Last Answer : (B) Spray
Description : Dried finished product sampled from various parts of a __________ dryer exhibits non-uniformity in the moisture content. (A) Rotary (B) Tray (C) Freeze (D) None of these
Last Answer : (B) Tray
Description : Large quantity of silica gel is normally dried in a __________ dryer. (A) Freeze (B) Through circulation (C) Rotary vacuum (D) Tray
Last Answer : (B) Through circulation
Description : Pick out the wrong statement pertaining to the rotary dryer. (A) Flights (located in the inside shell of rotary dryer) lift the material being dried and shower it down through the current of ... D) Recommended peripheral speed of a rotary drier is in the range of 10 to 30 metres/minute
Last Answer : (C) Rotary dryer is suitable for drying sticky materia
Description : Vacuum is applied in __________ zone, in case of a general type continuous rotary drum vacuum filter. (A) Filtering (B) Washing (C) Drying (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : Which of the following is not a continuous drier? (A) Drum drier (B) Spray drier (C) Tunnel drier (D) Tray drier
Last Answer : (D) Tray drier
Description : Flights in a rotary dryer are provided to (A) Lift and shower the solids thus exposing it thoroughly to the drying action of the gas (B) Reduce the residence time of solid (C) Increase the residence time of the solid (D) None of these
Last Answer : (A) Lift and shower the solids thus exposing it thoroughly to the drying action of the gas
Description : Rotary dryers cannot handle __________ materials. (A) Free flowing (B) Dry (C) Sticky (D) Granular
Last Answer : (C) Sticky
Description : Free flowing granular materials can be best dried in a __________ drier. (A) Rotary (B) Cylinder (C) Drum (D) Freeze
Description : Heat sensitive materials like certain pharmaceuticals and food stuffs can be dried in a/an __________ dryer. (A) Indirect tray (B) Spray (C) Freeze (D) None of these
Last Answer : (C) Freeze
Description : Pick up the correct statement from the following: (A) According to the petrological characteristics, concrete aggregates are classified as heavy weight, normal weight and light weight (B) According to ... glassy, smooth, granular, rough, crystalline, honey combed and porous (D) All the above
Last Answer : Answer: Option D
Description : Calcination of limestone to produce lime is done in a __________ kiln. (A) Tunnel (B) Rotary (C) Vertical shaft (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C)
Description : An improved and fuel efficient version of the pusher type reheating furnace is the __________ furnace. (A) Walking beam (B) Shaft (C) Tunnel (D) Rotary hearth
Last Answer : (A) Walking beam
Description : Dryer widely used in a textile industry is __________ dryer. (A) Festoon (B) Cylinder (C) Conveyor (D) Tunnel
Last Answer : (C) Conveyor
Description : In paper industry, paper is dried in a __________ dryer. (A) Tunnel (B) Heated cylinder (C) Conveyor (D) Festoon
Last Answer : (B) Heated cylinder
Description : For achieving rapid drying rate in a spray dryer, the diameter of the particles in the feed should be in the range of __________ microns (1 mm = 1000 microns). (A) 1-5 (B) 10-60 (C) 200-300
Last Answer : (B) 10-60
Description : __________ is a non volatile film forming constituent of a paint. (A) Thinner (B) Dryer (C) Drying oil (D) None of these
Last Answer : (C) Drying oil
Description : n a chemical factory where dyes are made, wet cake at 30 OC consisting of 60% moisture is put in a dryer to obtain an output having only 5% moisture, at atmospheric pressure. In each batch about 120 ... dryer and the dryer efficiency is 80%. Latent heat of steam at 4 kg/cm2 is 520 kcal/kg.
Last Answer : Given that Qty of material dried per batch - 120 Kgs Moisture at inlet - 60% a. The quantity of moisture removed per batch. Water quantity in a wet batch - 120 x 0.6 = 72 Kgs. Quantity of bone dry ... - 48/0.95 = 50.5 Kgs. Equivalent water in a dry batch - 50.5 - 48 = 2.5 Kgs.
Description : Wood is a/an __________ material. (A) Amorphous (B) Cellular (C) Homogeneous (D) Granular
Last Answer : (B) Cellular
Description : Large tonnage of refractory bricks are dried in a (A) Shaft furnace (B) Rotary hearth furnace (C) Tunnel kiln (D) Muffle furnace
Last Answer : (C) Tunnel kiln
Description : Cement Kiln is a (A) Rotary Kiln (B) Tunnel Kiln (C) Natural draft furnace (D) Batch furnace
Last Answer : (A) Rotary Kiln
Description : Which of the following is a periodic furnace? (A) Tunnel kiln (B) Rotary kiln (C) Soaking pit (D) Reheating furnace
Last Answer : (C) Soaking pit
Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.
Last Answer : i)Tray dryer: ii)Plate column: iii)Packed column: iv) Jaw crusher: v) Stirrer: vi) Ball mill
Description : Explain construction and application of tray dryer.
Last Answer : Construction of tray dryer. The simplest form of dryer , the source of heat ( electric heater or steam coil) is at floor level & relies on natural convection. Therefore no efficient ... of crude drugs 2)For chemicals 3)For powders 4)For Granules used in tablet manufacturing
Description : The most common drying method is ____ drying. a. freeze- c. spray b. sun or tray drying d. oven
Last Answer : c. spray
Description : ____ and ____ are already solid and lend themselves to sun or tray drying. a. Cheese, meats c. Cheese, vegetables b. Fruits, vegetables d. Fruits, meats
Last Answer : b. Fruits, vegetables
Description : Capacity of a rotary dryer depends on its (A) rpm (B) Inclination with ground surface (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) and (B)
Description : Which of the following employs an accessory known as 'drift eliminator'? (A) Multiple effect evaporator (B) Mechanical draft cooling tower (C) Rotary dryer (D) Rotating disc contacto
Last Answer : (B) Mechanical draft cooling tower
Description : Pick out the correct statement. (A) Higher hold up of the solid in the rotary dryer results in better exposure of the solids to the gas (B) The 'Hatta number' is ... reflux in case of distillation operation requires infinite number of plates for a binary system separation
Last Answer : (C) For a non-reacting binary mixture of ideal gases, the partial pressure distribution of both components is linear in the case of steady state equimolal counter-diffusion
Description : A slurry is to be dried to produce flaky solid. Which dryer would you recommend? (A) Spray dryer (B) Drum dryer (C) Rotary dryer (D) Dielectric drye
Last Answer : (A) Spray dryer
Description : The behaviour of visco-elastic material is time dependent. This behaviour is common in __________ materials. (A) Non-crystalline solid (B) Crystalline (C) Rubbery (D) Non-crystalline organic polymeric
Last Answer : (D) Non-crystalline organic polymeric
Description : Common house hold glass (i.e., soda-lime glass) is a/an __________ material. (A) Fully crystalline (B) Partly crystalline (C) Amorphous
Last Answer : (B) Partly crystalline
Description : Advantage of continuous drying over batch drying is that the (A) Drying cost per unit weight of dried product is less (B) Product with more uniform moisture content is produced (C) Equipment size required is smaller (D) All 'a', 'b' & 'c'
Last Answer : (D) All 'a', 'b' & 'c'
Description : How do I keep my dryer door from popping open during drying?
Last Answer : If you are having problems keeping your dryer door shut when the dryer is running, you want to check the door latch (or latches) along the inside of the door. One or more of these latches ... to be replaced. Replacement is a simple process and latches can typically be found at local hardware stores.
Description : Continuous injection system usually has a) plunger pump b) rotary pump c) gear pump d) vane pump
Last Answer : Answer: b Explanation: In common use continuous injection system usually has rotary pump.
Description : __________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron
Last Answer : (B) Belt
Description : Most suitable material for highway embankments is (A) Granular soil (B) Organic soil (C) Silts (D) Clays
Last Answer : Answer: Option A
Description : When the mixture to be distilled has a very high boiling point and the product material is heat sensitive, the separation technique to be used is __________ distillation. (A) Continuous (B) Steam (C) Azeotropic (D) None of these
Last Answer : (B) Steam
Description : Hydrogenation of oil is carried out in a/an __________ in Vanaspati manufacturing plant. (A) Agitated vessel (B) Sieve tray column (C) Bubble cap column (D) Packed tower
Last Answer : (A) Agitated vessel
Description : Tray spacing in a distillation column of dia 10-12 ft. used in petroleum refinery may be around __________ inches. (A) 5 (B) 30 (C) 60 (D) 100
Last Answer : (B) 30
Description : . __________ column is preferred to be used, when a high liquid hold up is required in a reactor for gas-liquid reaction. (A) Packed (B) Bubble (C) Spray (D) Tray
Last Answer : (B) Bubble
Description : Out of the following gas-liquid contacting devices, for a given set of operating conditions, gas pressure drop is the least in __________ tower. (A) Wetted wall (B) Bubble cap (C) Perforated tray (D) Packed
Last Answer : (A) Wetted wall
Description : Flooding in a vapor-liquid contacting equipment occurs in a tray, when the pressure drop through a tray is __________ the liquid head available in the downcomer. (A) Less than (B) More than (C) Same as (D) Very much less
Last Answer : (B) More than
Description : __________ column is used in gas absorption process. (A) Wetted wall (B) Sieve/perforated tray (C) Bubble cap (D) Packed
Last Answer : (D) Packed