Cermets are __________ materials. (A) Refractory (B) Reinforced (C) Abrasive (D) Fully metallic

Cermets are __________ materials.
(A) Refractory
(B) Reinforced
(C) Abrasive
(D) Fully metallic
by

1 Answer

Answer :

(A) Refractory
by

Related questions

In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet? (A) Zirconia (B) Alumina (C) Bakelite (D) Tungsten carbi

Description : In the formation of cermets, the ratio of ceramic material to metallic material is usually 80:20. Which of the following is a cermet? (A) Zirconia (B) Alumina (C) Bakelite (D) Tungsten carbi

Last Answer : Option D

Kaolin is a/an (A) Refractory material (B) Synthetic resin (C) Artificial abrasive (D) Blue pigment

Description : Kaolin is a/an (A) Refractory material (B) Synthetic resin (C) Artificial abrasive (D) Blue pigment

Last Answer : (A) Refractory material

Hot, lumpy & abrasive materials are best transported by using a/an __________ conveyor. (A) Apron (B) Belt

Description : Hot, lumpy & abrasive materials are best transported by using a/an __________ conveyor. (A) Apron (B) Belt

Last Answer : (A) Apron

__________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Description : __________ conveyor is the most suitable for long distance transportation of cold, non-abrasive granular/irregular shape/fine materials. (A) Bucket (B) Belt (C) Screw (D) Apron

Last Answer : (B) Belt

Wet sieving is employed, when the product contains __________ materials. (A) Abrasive (B) Large quantity of very fine (C) Coarse (D) Non-sticky

Description : Wet sieving is employed, when the product contains __________ materials. (A) Abrasive (B) Large quantity of very fine (C) Coarse (D) Non-sticky

Last Answer : (B) Large quantity of very fine

__________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Description : __________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Last Answer : (A) Flight

Which of the following conveyors cannot be recommended for transportation of abrasive materials? (A) Belt conveyor (B) Apron conveyor (C) Flight conveyor (D) Chain conveyor

Description : Which of the following conveyors cannot be recommended for transportation of abrasive materials? (A) Belt conveyor (B) Apron conveyor (C) Flight conveyor (D) Chain conveyor

Last Answer : (C) Flight conveyor

Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Description : Screw conveyors are (A) Run at very high rpm (B) Suitable for sticky materials (C) Suitable for highly abrasive materials (D) All (A), (B) and (C)

Last Answer : (B) Suitable for sticky materials

Soft & non-abrasive materials can be made into fines by (A) Attrition (B) Compression (C) Cutting (D) None of these

Description : Soft & non-abrasive materials can be made into fines by (A) Attrition (B) Compression (C) Cutting (D) None of these

Last Answer : (A) Attrition

hich of the following is the most suitable abrasive for grinding high tensile strength materials? (A) Silicon carbide (B) Corundum (C) Aluminium oxide (D) Boron carbide

Description : hich of the following is the most suitable abrasive for grinding high tensile strength materials? (A) Silicon carbide (B) Corundum (C) Aluminium oxide (D) Boron carbide

Last Answer : Option C

The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength of the insulation B. the paint dust is composed of abrasive and semi-conducting materials which impair insulation C. paint dust buildup has a tendency to cause corrosion D. phase windings frequently become isolated from each other due to dust interference at the terminals

Description : The removal of paint from electrical equipment, such as generators, should be cautiously undertaken because ____________. A. the mechanical shock of paint removal lessens the dielectric strength ... phase windings frequently become isolated from each other due to dust interference at the terminals

Last Answer : Answer: B

Which of the following is not a dielectric material? (A) Cotton, silk and paper (B) Asbestos, glass, porcelain and mica (C) Rubber and polymeric resins (D) All refractory materials

Description : Which of the following is not a dielectric material? (A) Cotton, silk and paper (B) Asbestos, glass, porcelain and mica (C) Rubber and polymeric resins (D) All refractory materials

Last Answer : Option C

Cermets are used for making (A) Cutting tools (B) Abrasives (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Cermets are used for making (A) Cutting tools (B) Abrasives (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Which of the following is not used as the ceramic material in ‘cermets’? (A) Silicides (B) Oxides (C) Carbides (D) Nitrides

Description : Which of the following is not used as the ceramic material in ‘cermets’? (A) Silicides (B) Oxides (C) Carbides (D) Nitrides

Last Answer : (D) Nitrides

Combination of metals and ceramics are called (A) Metalloy (B) Cermets (C) Pellets (D) Non-crystalline ceramics

Description : Combination of metals and ceramics are called (A) Metalloy (B) Cermets (C) Pellets (D) Non-crystalline ceramics

Last Answer : (B) Cermets

Which of the following is not used as a bearing material? (A) Copper-lead alloys (B) Babbitts (C) Bronzes (D) Cermets

Description : Which of the following is not used as a bearing material? (A) Copper-lead alloys (B) Babbitts (C) Bronzes (D) Cermets

Last Answer : Option D

Drills are usually made of (A) Cermets (B) High speed steel (C) Alloy steel (D) Tungsten carbide

Description : Drills are usually made of (A) Cermets (B) High speed steel (C) Alloy steel (D) Tungsten carbide

Last Answer : Option B

Broaching tools are usually made of (A) Cermets (B) High speed steel (C) Tungsten carbide (D) Stellite

Description : Broaching tools are usually made of (A) Cermets (B) High speed steel (C) Tungsten carbide (D) Stellite

Last Answer : Option B

In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Description : In an over-reinforced section (a) Steel reinforcement is not fully stressed to its permissible value (b) Concrete is not fully stressed to its permissible value (c) Either (a) and (b) (d) Both (a) and (b)

Last Answer : (a) Steel reinforcement is not fully stressed to its permissible value

The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Description : The section in which concrete is not fully stressed to its permissible value when stress in steel reaches its maximum value is (a) Under-reinforced section (b) Over-reinforced section (c) Critical section (d) Balanced section

Last Answer : (a) Under-reinforced section

The damage/deterioration of metals by the __________ action of fluids is called 'erosion'. (A) Abrasive (B) Corrosive (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The damage/deterioration of metals by the __________ action of fluids is called 'erosion'. (A) Abrasive (B) Corrosive (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (A) Abrasive

The sequence of refractory materials according to increasing melting points is: (A) Dolomite, Magnesia, Bauxite, Chromites (B) Bauxite, Chromites, Dolomite, Magnesia (C) Magnesia, Bauxite, Dolomite, Chromites (D) None of these

Description : The sequence of refractory materials according to increasing melting points is: (A) Dolomite, Magnesia, Bauxite, Chromites (B) Bauxite, Chromites, Dolomite, Magnesia (C) Magnesia, Bauxite, Dolomite, Chromites (D) None of these

Last Answer : Answer: Option B

Refractory bricks are usually dried in a __________ dryer. (A) Tray (B) Tunnel (C) Conveyor (D) Festoon

Description : Refractory bricks are usually dried in a __________ dryer. (A) Tray (B) Tunnel (C) Conveyor (D) Festoon

Last Answer : (B) Tunnel

Drying of refractory is normally carried out in a __________ dryer. (A) Open pan (B) Tray (C) Rotary vacuum (D) Truck/tunnel

Description : Drying of refractory is normally carried out in a __________ dryer. (A) Open pan (B) Tray (C) Rotary vacuum (D) Truck/tunnel

Last Answer : (D) Truck/tunnel

Fire clay is __________ refractory material. (A) A basic (B) An acidic (C) A neutral (D) Not a

Description : Fire clay is __________ refractory material. (A) A basic (B) An acidic (C) A neutral (D) Not a

Last Answer : (B) An acidic

A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of thermal conductivity 0.14 W/m.K and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5

Last Answer : (B) 0.1

__________ is used for tying the steel columns to concrete foundation. (A) Grouting (B) Eyebolt (C) Anchor bolts (D) Refractory castables

Description : __________ is used for tying the steel columns to concrete foundation. (A) Grouting (B) Eyebolt (C) Anchor bolts (D) Refractory castables

Last Answer : C) Anchor bolts

__________ property of steel increases by addition of large amount of silicon in it. (A) Mechanical (B) Machining (C) Magnetic (D) Refractory

Description : __________ property of steel increases by addition of large amount of silicon in it. (A) Mechanical (B) Machining (C) Magnetic (D) Refractory

Last Answer : Option C

How good are Carbon Fibre reinforced Composite Materials at stopping Bullets?

Description : How good are Carbon Fibre reinforced Composite Materials at stopping Bullets?

Last Answer : There’s a thread on this subject with interesting points on a gun DB I’m not an expert on this subject at all, but I thought carbon fiber was too breakable (I’m into cars)

A flywheel is made of 1. cast iron 2. high strength steels 3. graphic fiber reinforced polymer 4. any one of the above materials

Description : A flywheel is made of 1. cast iron 2. high strength steels 3. graphic fiber reinforced polymer 4. any one of the above materials

Last Answer : 4. any one of the above materials

Epoxy resin is (A) Not used for surface coating (B) A good abrasive (C) An elastomer (D) A polyester

Description : Epoxy resin is (A) Not used for surface coating (B) A good abrasive (C) An elastomer (D) A polyester

Last Answer : (B) A good abrasive

. In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal

Silicon carbide is a/an (A) Adhesive (B) Abrasive (C) Type of glass (D) Brittle material

Description : Silicon carbide is a/an (A) Adhesive (B) Abrasive (C) Type of glass (D) Brittle material

Last Answer : (B) Abrasive

Which of the following is not an abrasive material? (A) Bakelite (B) Pumice (C) Corundum (D) Carborundum

Description : Which of the following is not an abrasive material? (A) Bakelite (B) Pumice (C) Corundum (D) Carborundum

Last Answer : (A) Bakelite

Zeolite is a/an (A) Naturally occuring clay which is capable of exchanging cations (B) Abrasive material (C) Catalyst used in shift conversion (D) None of these

Description : Zeolite is a/an (A) Naturally occuring clay which is capable of exchanging cations (B) Abrasive material (C) Catalyst used in shift conversion (D) None of these

Last Answer : (A) Naturally occuring clay which is capable of exchanging cations

Finely ground calcium aluminate & silicate is a/an (A) Cermet (B) Cement (C) Abrasive (D) Explosive

Description : Finely ground calcium aluminate & silicate is a/an (A) Cermet (B) Cement (C) Abrasive (D) Explosive

Last Answer : (B) Cement

Phenol formaldehyde (A) Employs addition polymerisation (B) Employs condensation polymerisation (C) Is a monomer (D) Is an abrasive material

Description : Phenol formaldehyde (A) Employs addition polymerisation (B) Employs condensation polymerisation (C) Is a monomer (D) Is an abrasive material

Last Answer : (B) Employs condensation polymerisation

What materials are commonly used as cushions between cable insulation and metallic armor?

Description : What materials are commonly used as cushions between cable insulation and metallic armor?

Last Answer : Jute and Asphalt coverings.

Cast iron detachable joint is used in __________ pipes. (A) Steel (B) Cast iron (C) Asbestos cement (D) Reinforced cement concrete

Description : Cast iron detachable joint is used in __________ pipes. (A) Steel (B) Cast iron (C) Asbestos cement (D) Reinforced cement concrete

Last Answer : (A) Steel

Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Description : Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Last Answer : (B) Tensile

Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint. (A) Flanged iron (B) Collar (C) Flexible (D) Expansion

Description : Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint. (A) Flanged iron (B) Collar (C) Flexible (D) Expansion

Last Answer : Option B

Modern Society question: Do you feel that being rude, abrasive, sarcastic, or apathetic are the new norms for acceptable behavior and ettiquette?

Description : Modern Society question: Do you feel that being rude, abrasive, sarcastic, or apathetic are the new norms for acceptable behavior and ettiquette?

Last Answer : There has always been rude, abrasive, sarcastic, or apathetic people. I would start with the need of a two paycheck household. A child gets better direction when a parent is home to guide them.

Abrasive exhaust - corrosion

Description : When crossing the curb, I probably stuck in the underside of the car and during the visual inspection I noticed that the exhaust cabin is slightly frayed. On another forum, I learned that the anti- ... given place? Or would the exhaust cell start to corrode? Thank you for your answers and responses.

Last Answer : I wouldn't deal with it personally. Corrosion will sooner or later burn the exhaust and you will change it. Even if it is scratched, it will not significantly reduce the service life of the exhaust.

Trinitrotoluene is – (1) used to melt metals (2) used to fuse two metals (3) used as an abrasive (4) used as an explosive

Description : Trinitrotoluene is – (1) used to melt metals (2) used to fuse two metals (3) used as an abrasive (4) used as an explosive

Last Answer : (4) used as an explosive Explanation: Trinitrotoluene (C6H2 (NO2)3.CH3), abbreviated as TNT, is sometimes used as a reagent in chemical synthesis, but it is best known as an explosive material ... The explosive yield of TNT is considered to be the standard mea-sure of bombs and other explosives.

All of the following items can be used in the maintenance of a D.C. propulsion motor's commutator EXCEPT _______________. A. a canvas wiper B. safety solvent C. abrasive dressing stones D. sandpaper

Description : All of the following items can be used in the maintenance of a D.C. propulsion motor's commutator EXCEPT _______________. A. a canvas wiper B. safety solvent C. abrasive dressing stones D. sandpaper

Last Answer : Answer: B

Give reason Why Diamond is used as abrasive?

Description : Give reason Why Diamond is used as abrasive?

Last Answer : Ans. because it is the hardest substance . All the four valencies are filled.

Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Description : Extreme Pressure (EP) additives cause ______ wear in the bearing parts. (a) abrasive (b) corrosive (c) pitting (d) fatigue

Last Answer : (b) corrosive

The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Description : The property of the bearing material to allow the dust and abrasive particles to get absorbed on the surface of the lining is called (A) Embeddability (B) Conformability (C) Viscosity (D) Endurance limit stress

Last Answer : (A) Embeddability

Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Description : Extreme pressure causes ______ wear in the bearing parts. a) Abrasive b) Corrosive c) Pitting d) All of the mentioned

Last Answer : b) Corrosive