Diesel index is defined as (A) (°API) × (Aniline Point, °F)/100 (B) (°API) × (Aniline Point, °C)/100 (C) (°API) × (100)/Aniline Point, °F (D) (°API) × (100)/Aniline Point, °C

Diesel index is defined as
(A) (°API) × (Aniline Point, °F)/100
(B) (°API) × (Aniline Point, °C)/100
(C) (°API) × (100)/Aniline Point, °F
(D) (°API) × (100)/Aniline Point, °C
by

1 Answer

Answer :

(A) (°API) × (Aniline Point, °F)/100
by

Related questions

Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150

Description : Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150

Last Answer : (B) 70

High aniline point of diesel indicates that, it (A) Is highly aromatic (B) Has a large ignition delay (C) Is highly paraffinic (D) Has a low diesel index

Description : High aniline point of diesel indicates that, it (A) Is highly aromatic (B) Has a large ignition delay (C) Is highly paraffinic (D) Has a low diesel index

Last Answer : (C) Is highly paraffinic

Diesel index (an alternative index for expressing the quality of diesel) is (A) Determined by using a test engine (B) Not related to aniline point (C) Equal to cetane number plus 3 (D) All (A), (B) & (C)

Description : Diesel index (an alternative index for expressing the quality of diesel) is (A) Determined by using a test engine (B) Not related to aniline point (C) Equal to cetane number plus 3 (D) All (A), (B) & (C)

Last Answer : (C) Equal to cetane number plus 3

High aniline point of a petrofuel (say diesel) indicates that (A) It is highly aromatic in nature (B) It is highly paraffinic in nature (C) It has a very low diesel index (D) Its ignition quality is very poor

Description : High aniline point of a petrofuel (say diesel) indicates that (A) It is highly aromatic in nature (B) It is highly paraffinic in nature (C) It has a very low diesel index (D) Its ignition quality is very poor

Last Answer : (B) It is highly paraffinic in nature

Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8 (A) °C (B) °F (C) °K (D) °R

Description : Melting point & boiling points of liquid oxygen are respectively - 218.8°C & - 183°C, while the same for liquid nitrogen is - 210°C & - 195.8°C respectively. The difference in melting points of liquid oxygen & liquid nitrogen is not equal to 8.8 (A) °C (B) °F (C) °K (D) °R

Last Answer : (B) °F

212 °F = _____ °C  a. 200  b. 150  c. 100  d. None of the above

Description : 212 °F = _____ °C  a. 200  b. 150  c. 100  d. None of the above

Last Answer : 100

Which of the following fractions of a crude oil will have the maximum gravity API (i.e. °API)? (A) Diesel (B) Gasoline (C) Atmospheric gas oil (D) Vacuum gas oil

Description : Which of the following fractions of a crude oil will have the maximum gravity API (i.e. °API)? (A) Diesel (B) Gasoline (C) Atmospheric gas oil (D) Vacuum gas oil

Last Answer : (C) Atmospheric gas oil

Which of the following has the maximum °API gravity of all? (A) Diesel(B) Kerosene(C) Petrol(D) Furnace oil

Description : Which of the following has the maximum °API gravity of all? (A) Diesel (B) Kerosene (C) Petrol (D) Furnace oil

Last Answer : (C) Petrol

Which of the following has the minimum °API gravity of all? (A) Diesel (B) Kerosene (C) Petrol (D) Furnace oil

Description : Which of the following has the minimum °API gravity of all? (A) Diesel (B) Kerosene (C) Petrol (D) Furnace oil

Last Answer : (D) Furnace oil

1 BTU/hr.ft.°F is equal to __________ kcal/hr. m.°C. (A) 1.49 (B) 1 (C) 4.88 (D) None of these

Description : 1 BTU/hr.ft.°F is equal to __________ kcal/hr. m.°C. (A) 1.49 (B) 1 (C) 4.88 (D) None of these

Last Answer : (A) 1.49

Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity (C) In unsteady state heat conduction, heat flows in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Description : Pick out the correct statement. (A) 1 kcal/hr.m.°C is equal to 1 BTU/hr. ft.°F (B) In steady state heat conduction, the only property of the substance which determines the ... in the direction of temperature rise (D) In heat transfer by forced convection, Grashoff number is very important

Last Answer : (B) In steady state heat conduction, the only property of the substance which determines the temperature distribution, is the thermal conductivity

Optimum preheating temperature for pitch creosote mixture (PCM) which is also termed as C.T.F-200, before atomisation through burners is (A) 200 °F (B) 200 °C (C) 200 °K (D) 200 °R

Description : Optimum preheating temperature for pitch creosote mixture (PCM) which is also termed as C.T.F-200, before atomisation through burners is (A) 200 °F (B) 200 °C (C) 200 °K (D) 200 °R

Last Answer : (A) 200 °F

What is the formula to convert °F to °C?  a) °C = °F + 273  b) °C = 5/9 (°F - 32)  c) °C = 9/5 (°F)+32  d) None of the above

Description : What is the formula to convert °F to °C?  a) °C = °F + 273  b) °C = 5/9 (°F - 32)  c) °C = 9/5 (°F)+32  d) None of the above

Last Answer : °C = 5/9 (°F - 32)

What is the formula to convert °C to °F?  a) °F = °C + 273  b) °F = 5/9 (°C - 32)  c) °F = 9/5 (°C)+32  d) None of the above

Description : What is the formula to convert °C to °F?  a) °F = °C + 273  b) °F = 5/9 (°C - 32)  c) °F = 9/5 (°C)+32  d) None of the above

Last Answer : momentum

What is the SI unit of specific heat capacity?  A. J/kg  B. J/kg °F ∙  C. J/kg °C ∙  D. J/°C

Description : What is the SI unit of specific heat capacity?  A. J/kg  B. J/kg °F ∙  C. J/kg °C ∙  D. J/°C

Last Answer : J/kg °C

Aniline point is the (A) Characteristic property of diesel & lubricating oils (B) Measure of aromatic content of oil (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Aniline point is the (A) Characteristic property of diesel & lubricating oils (B) Measure of aromatic content of oil (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B

Aniline point of the diesel is a measure of its __________ content. (A) Aromatic (B) Paraffin (C) Olefin (D) Naphthene

Description : Aniline point of the diesel is a measure of its __________ content. (A) Aromatic (B) Paraffin (C) Olefin (D) Naphthene

Last Answer : (B) Paraffin

Aniline point is a property of the (A) Diesel (B) LPG (C) Naphtha (D) Gasoline

Description : Aniline point is a property of the (A) Diesel (B) LPG (C) Naphtha (D) Gasoline

Last Answer : (C) Naphtha

Equal volumes of aniline and diesel oil when mixed at room temperature (during summer) was found to be completely miscible. It means that the aniline point of the diesel is __________ the room temperature. (A) More than (B) Less than (C) Same as (D) Either more or less; depends on the room temperature

Description : Equal volumes of aniline and diesel oil when mixed at room temperature (during summer) was found to be completely miscible. It means that the aniline point of the diesel is __________ the room temperature. (A) ... (B) Less than (C) Same as (D) Either more or less; depends on the room temperature

Last Answer : (C) Same as

Aniline point is the temperature at which (A) Equal weight of diesel & the aniline are completely miscible (B) Equal weight of aniline & the test sample are completely miscible (C) Equal volume of aniline & the test sample are completely miscible (D) Aniline vaporises

Description : Aniline point is the temperature at which (A) Equal weight of diesel & the aniline are completely miscible (B) Equal weight of aniline & the test sample are completely miscible (C) Equal volume of aniline & the test sample are completely miscible (D) Aniline vaporises

Last Answer : (C) Equal volume of aniline & the test sample are completely miscible

A multigrade lubricating oil means an oil having high (A) Viscosity index (B) Viscosity (C) Aniline point (D) Flash point

Description : A multigrade lubricating oil means an oil having high (A) Viscosity index (B) Viscosity (C) Aniline point (D) Flash point

Last Answer : (A) Viscosity index

Pick out the additive property of lube oil out of following. (A) °API gravity (B) Specific gravity (C) Viscosity (D) Flashpoint

Description : Pick out the additive property of lube oil out of following. (A) °API gravity (B) Specific gravity (C) Viscosity (D) Flashpoint

Last Answer : (A) °API gravity

Flash point of motor gasoline may be around __________ °C. (A) 10 (B) 45 (C) 100 (D) 150

Description : Flash point of motor gasoline may be around __________ °C. (A) 10 (B) 45 (C) 100 (D) 150

Last Answer : (B) 45

Nitrobenzene (boiling point = 210.6°C) is steam distilled at 1 atm pressure. Nitrobenzene will distil off __________ °C. (A) At < 100 (B) At > 210.6 (C) Between 100 and 210 (D) None of these

Description : Nitrobenzene (boiling point = 210.6°C) is steam distilled at 1 atm pressure. Nitrobenzene will distil off __________ °C. (A) At < 100 (B) At > 210.6 (C) Between 100 and 210 (D) None of these

Last Answer : (A) At < 100

Flash point of most vegetable oils is about __________ °C. (A) 50 (B) 100 (C) 200 (D) 300

Description : Flash point of most vegetable oils is about __________ °C. (A) 50 (B) 100 (C) 200 (D) 300

Last Answer : (C) 200

Work index is defined as the (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen (B) Energy needed to crush one tonne of feed to 200 microns (C) Energy (kWh/ton of feed) needed to crush small feed to such a size that 80% of the product passes a 200 mesh screen (D) Energy needed to crush one ton of feed to 100 microns

Description : Work index is defined as the (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen (B) Energy needed to crush ... of the product passes a 200 mesh screen (D) Energy needed to crush one ton of feed to 100 microns

Last Answer : (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen

The unit of heat transfer co-efficient is (A) BTU/hr. ft 2°F (B) BTU/hr. °F. ft (C) BTU/hr. °F (D) BTU/hr. ft

Description : The unit of heat transfer co-efficient is (A) BTU/hr. ft 2°F (B) BTU/hr. °F. ft (C) BTU/hr. °F (D) BTU/hr. ft

Last Answer : (A) BTU/hr. ft 2°F

A BTU/hr.ft. 2 °F is equal to (A) 1 kcal/hr. m2°C (B) 4.88 kcal/hr. m. 2°C (C) 1 kcal/hr. m2 .°K (D) None of these

Description : A BTU/hr.ft. 2 °F is equal to (A) 1 kcal/hr. m2°C (B) 4.88 kcal/hr. m. 2°C (C) 1 kcal/hr. m2 .°K (D) None of these

Last Answer : (B) 4.88 kcal/hr. m. 2°C

Pensky-Marten apparatus is used for those oils, whose flash points are __________ °F. (A) < 120 (B) > 120 (C) < 90 (D) 90-110

Description : Pensky-Marten apparatus is used for those oils, whose flash points are __________ °F. (A) < 120 (B) > 120 (C) < 90 (D) 90-110

Last Answer : (B) > 120

Aniline point test of an oil qualitatively indicates the __________ content of an oil. (A) Paraffin (B) Olefin (C) Aromatic (D) Naphthene

Description : Aniline point test of an oil qualitatively indicates the __________ content of an oil. (A) Paraffin (B) Olefin (C) Aromatic (D) Naphthene

Last Answer : (C) Aromatic

Illuminating characteristics of kerosene is expressed by its (A) Smoke point (B) Aniline point (C) Luminosity number (D) Aromatic content

Description : Illuminating characteristics of kerosene is expressed by its (A) Smoke point (B) Aniline point (C) Luminosity number (D) Aromatic content

Last Answer : (C) Luminosity number

Which of the following tests is not done for transformer oil? (A) Flash point and acid value (B) Aniline point (C) Dielectric strength (D) Copper strip corrosion test

Description : Which of the following tests is not done for transformer oil? (A) Flash point and acid value (B) Aniline point (C) Dielectric strength (D) Copper strip corrosion test

Last Answer : (B) Aniline poin

Which of the following is not an important property of fuel oil/furnace oil? (A) Sulphur content (B) Viscosity (C) Aniline point (D) Flash point

Description : Which of the following is not an important property of fuel oil/furnace oil? (A) Sulphur content (B) Viscosity (C) Aniline point (D) Flash point

Last Answer : (C) Aniline point

Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Description : Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280

Last Answer : (D) 250-280

Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450

Description : Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450

Last Answer : (B) 150

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Description : Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150

Last Answer : (C) 150

The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850

Description : The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850

Last Answer : (B) 350 to 450

Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Description : Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Last Answer : (A) 700 - 1000

Fermentation of molasses to produce ethyl alcohol is done at __________ °C. (A) 20 - 30 (B) < - 5 (C) 100 - 150 (D) 250 - 300

Description : Fermentation of molasses to produce ethyl alcohol is done at __________ °C. (A) 20 - 30 (B) < - 5 (C) 100 - 150 (D) 250 - 300

Last Answer : (A) 20 - 30

Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0

Description : Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0

Last Answer : (A) 15-30

What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600

Description : What is the range of tempering temperature (°C) for most of the materials? (A) 75-100 (B) 200-300 (C) 350-450 (D) 500-600

Last Answer : (B) 200-300

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

The normal body temperature of human beings is - (1) 96.4 °F (2) 97.4 °F (3) 98.4 °F (4) 99.4 °F

Description : The normal body temperature of human beings is - (1) 96.4 °F (2) 97.4 °F (3) 98.4 °F (4) 99.4 °F

Last Answer : (3) 98.4 °F' Explanation: The normal core body temperature of a healthy, resting adult human being is stated to be at 98.6 degrees fahrenheit or 37.0 degrees celsius. Though the body ... the higher the normal body temperature or the slower the metabolic rate the lower the normal body temperature.

A System has a temperature of 250°F. Convert this Value to °R?  a. 740°R  b.730°R  c. 720°R  d. 710°R formula: °R= °F + 460

Description : A System has a temperature of 250°F. Convert this Value to °R?  a. 740°R  b.730°R  c. 720°R  d. 710°R formula: °R= °F + 460

Last Answer : 710°R

212 °F = _____R  a. 567  b. 672  c. 700  d. None of the above

Description : 212 °F = _____R  a. 567  b. 672  c. 700  d. None of the above

Last Answer : 672

876 °R = _____ °F  a. 335  b. 416  c. 400  d. None of the above

Description : 876 °R = _____ °F  a. 335  b. 416  c. 400  d. None of the above

Last Answer : 416

746 °R = ______ °F  a. 254  b. 345  c. 286  d. None of the above

Description : 746 °R = ______ °F  a. 254  b. 345  c. 286  d. None of the above

Last Answer : 286

The normal body temperature of human beings is (1) 96.4 °F (2) 97.4 °F (3) 98.4 °F (4) 99.4 °F

Description : The normal body temperature of human beings is (1) 96.4 °F (2) 97.4 °F (3) 98.4 °F (4) 99.4 °F

Last Answer :  98.4 °F

Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205

Description : Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205

Last Answer : (B) 135