Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b d. None of these.
Last Answer : ANSWER c. Both a and b.
Description : The knocking in spark ignition engines can be reduced by a. Retarding the spark. b. Increasing the engine speed. c. Both a and b. d. None of these.
Last Answer : ANSWER c. Both a and b
Description : The fuel in diesel engine is normally injected at pressure of a. 5-10 kg/cm2 b. 20-25 kg/cm2 c 60-80 kg/cm2 d. 90-130 kg/cm2
Last Answer : ANSWER d. 90-130 kg/cm2
Description : The efficiency of a internal combustion engine normally is of the order of a. 15-20 % b. 20-25% c. 25-30% d. 30-35%
Last Answer : ANSWER d. 30-35%
Description : A 5 BHP engine running at full load would consume diesel of the order of A. 0.3 kg/hr B. 1 kg/hr C. 3 kg/hr D. 5 kg/hr
Last Answer : ANSWER ; B
Description : A diesel engine compared to petrol engine, running at full load is A. less efficient B. equally efficient C. more efficient D. other factors will decide it
Last Answer : ANSWER : C
Description : The output of a diesel engine can be increased without increasing the engine speed or size in the following way A. feeding more fuel B. increasing the flywheel size C. heating intake air D. supercharging
Last Answer : ANSWER : D
Description : The ___________ sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load. a) throttle position b) manifold pressure c) camshaft position d) knock
Last Answer : Answer: b Explanation: The manifold pressure sensor, monitors vacuum in the engine intake manifold so that the mixture strength can be adjusted with changes in engine load and the camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection.
Description : A 40 kW engine has a mechanical efficiency of 80 %. If the frictional power is assumed to be constant with load, what is the approximate value of the mechanical efficiency at 50 % of the rated load? (a) 45% (b) 55 % (c) 65% (d) 75%
Last Answer : Ans :c
Description : For low load operation more economical engine is a. petrol engine b. diesel engine c. muticylinder engine d. two stroke engine
Last Answer : ANSWER b. diesel engine
Description : For same compression ratio a. Diesel cycle has lower efficiency than Otto cycle b. Diesel cycle has higher efficiency than Otto cycle c. Diesel cycle and Otto cycle have equal efficiencies d. Depends upon the load on engine
Last Answer : Answer a. Diesel cycle has lower efficiency than Otto cycle
Description : What is sensible cooling of air? A. the cooling in which sensible heat of air is removed in order to reduce temperature B. the cooling in which temperature of air is reduced without changing in its moisture content C. both a. and b. D. none of the above
Description : In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°
Last Answer : ANSWER : A
Description : Air fuel ratio for idling speed of a petrol engine is approximately A. 1:1 B. 5:1 C. 20:1 D. 10:1
Description : Most high speed compression ignition engine operate on A. dual cycle B. otto cycle C. diesel cycle D.Carnot cycle
Description : In a battery ignition system, the intensity of spark is A. minimum at low engine speed B. minimum at low engine speed and increases with engine speed C. maximum al low engine speed and decreases with engine speed D. maximum at low engine speed
Description : Supercharging of an IC engine is done so that the A. thermal efficiency increases B. power output increases C. speed of the engine increases D. power output decreases
Last Answer : ANSWER : B
Description : An engine indicator is used to determine the following A. Speed B. Temperature C. M.E.P D. Volume of cylinder
Description : The _____________ sensor, senses rotation of engine camshaft for speed and timing of injection. a) throttle position b) manifold pressure c) camshaft position d) knock
Last Answer : Answer: c Explanation: The camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection whereas the throttle position sensor, senses the movement of the throttle ... engine intake manifold so that the mixture strength can be adjusted with changes in engine load.
Description : The _____________ sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration. a) throttle position b) manifold pressure c) camshaft position d) knock
Last Answer : Answer: a Explanation: The throttle position sensor, senses the movement of the throttle plate so that the mixture flow can be adjusted for engine speed and acceleration while the manifold ... the camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection.
Description : In a variable speed SI engine, the maximum torque occurs at the maximum (a) Speed (b) Brake power (c) Indicated power (d) Volumetric efficiency
Last Answer : Ans :d
Description : A two stroke engine has a speed of 750 rpm. A four stroke engine having an identical cylinder size runs at 1500 rpm. The theoretical output of the two stroke engine will (a) Be twice that of the four stroke ... ) Be the same as that of the four stoke (d) Depend upon whether it is a CI or SI engine
Description : An engine indicator is used to determine the following a. Speed. b. Temperature. c. Volume of cylinder. d. Mean effective pressure and Indicated horse power.
Last Answer : ANSWER d. Mean effective pressure and Indicated horse power.
Description : A engine will generate maximum torque when it a. runs at maximum speed b. develops maximum power c. runs at lowest speed d. consumes more fuel
Last Answer : ANSWER c. runs at lowest speed
Description : The tendency of a diesel engine to knock increases if a. engine speed is increased b. engine power is increased c. cetane number of the fuel is increased d. compression ratio is increased
Last Answer : ANSWER d. compression ratio is increased
Description : HUCR is the highest compression ratio at which the A. engine can be run B. engine gives maximum output C. engine is most efficient D. fuel can be used in a test engine without detonation
Description : In a petrol engine, which of the following gas gets exhausted out without burning and without transformation? a. CO2 b. CO c. O2 d. N2
Last Answer : ANSWER d. N2
Description : The output of a diesel engine can be increased without increasing the engine size in following way a. injecting more fuel b. increasing flywheel size c. scavenging d. supercharging
Last Answer : ANSWER d. supercharging
Description : Absorption system normally uses the following refrigerant (a) Freon-11 (b) Freon-22 (c) C02 (d) ammonia.
Last Answer : Ans: e
Description : Octane number of petrol normally used in petrol engines is of the order of a. 20-30 b. 40-60 c. 60-70 d. 80-90
Last Answer : ANSWER d. 80-90
Description : In SI engines knocking can be reduced by (a) Increasing the compression ratio (b) Increasing the cooling water temperature (c) Retarding the spark advance (d) Increasing the inlet air temperature
Description : A large clearance volume in a reciprocating compressor results in A. Reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure
Description : A large clearance volume in reciprocating compressor results in A. reduced volume flow rate B. Increased volume flow rate C. Lower suction pressure D. Lower delivery pressure
Description : Motoring test is conducted on IC engines to determine A. brake power B. indicated power C. friction power D. fuel consumption at full load
Description : Efficiency of a Carnot engine is given as 80%. If the- cycle direction be reversed, what will be the value of COP ofreversed Carnot cycle (a) 1.25 (b) 0.8 (c) 0.5 (d) 0.25
Last Answer : Ans: d
Description : In two stroke engine one power occurs in _______ of crank rotation A. 180° B. 360° C. 270° D. 720°
Description : In a naturally aspirated diesel engine, the air is supplied by a A. supercharger B. centrifugal pump C. movement of engine piston D. reciprocating pump
Description : The knock in diesel engine occurs due to A. instantaneous and rapid burning of the first part of the charge B. instantaneous auto ignition of the last part of the charge C. delayed burning of the last part of the charge D. reduction of delay period
Description : Air fuel ratio at which a petrol engine cannot work is A. 8:1 B. 12:1 C. 15:1 D. 20:1 and less
Description : The theoretically correct air fuel ratio of a petrol engine is of the order of A. 6:1 B. 10:1 C. 15:1 D. 20:1
Description : The reason for supercharging in any engine is to be A. increase efficiency B. increase power C. effect fuel economy D. reduce weight and bulk for a given output
Description : The actual volume of fresh charge admitted in 4-stroke petrol engine is A. equal to stroke volume B. equal stroke volume and clearance volume C. less than stroke volume D. more than stroke volume
Description : The fuel air ratio in a petrol engine fitted with suction carburetor, operating with dirty air filter as compared to clean filter will be A. higher B. lower C. remain unaffected D. unpredictable
Description : The size of inlet valve of an engine in comparison to exhaust valve is A. more B. less C. same D. varies from design to design
Description : Octane number of gasoline is obtained by comparing the performance of the engine when running on a mixture of the following hydrocarbons A. ethane and methane B. normal heptane and iso-octane C. iso-heptane and octane D. iso-octane and TEL
Description : Solid injection in CI engine means injection of A. solid fuel only B. liquid fuel only C. liquid fuel and air D. solid fuel and air
Description : Ignition timing of a multi-cylinder SI engine can be adjusted by A. rotating the cam shaft B. adjusting the generator pulley C. rotating the distributor D. adjusting the pump pulley
Description : By supercharging the power output of an engine is expected to increase by A. 20% B. 45% C. 75% D. 50%
Description : Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine
Description : The specific fuel consumption of a petrol engine compared to diesel engine of same H.P is A. same B.more C. less D. unpredictable