Which of the following terminology is not used for size reduction of materials to fine sizes or powders? (A) Comminution (B) Dispersion (C) Pulverisation (D) Compression

Which of the following terminology is not used for size reduction of
materials to fine sizes or powders?
(A) Comminution
(B) Dispersion
(C) Pulverisation
(D) Compression
by

1 Answer

Answer :

(D) Compression
by

Related questions

Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Description : General mechanism of size reduction in intermediate and fine grinder is by (A) Cutting action (B) Compression (C) Compression and tearing (D) Impact and attrition

Last Answer : (D) Impact and attrition

Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C) Curing of concrete is done for proper compaction of cement (D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Description : Pick up the correct statement from the following: (A) Plain cement concrete is equally strong in compression as well as in tension (B) Slump test is performed to check concrete strength (C ... D) Fineness modulus is the index number expressing the relative sizes of both coarse and fine aggregates

Last Answer : Option D

Which of the following is not an additive for flue gases from furnace to reduce its dew-point? (A) Ammonia (B) Fine dolomite (C) Alkaline powders (D) None of these

Description : Which of the following is not an additive for flue gases from furnace to reduce its dew-point? (A) Ammonia (B) Fine dolomite (C) Alkaline powders (D) None of these

Last Answer : (D) None of these

There are a multitude of various dressings available. Which of the following statement(s) is/are true concerning options for surgical dressings? a. Hydrocolloids, such as karaya compounds, offer the primary advantage of increased absorptive ability b. Films, such as Op-site, provide a water impermeable environment to achieve a dry wound c. Impregnates are fine gauze impregnated with a variety of substances such as antibiotics or moisturizing agents that adhere tightly to the wound and do not require a secondary dressing d. Absorptive powders and paste are highly useful in debriding necrotic and fibrous material from wounds and absorbing wound serum

Description : There are a multitude of various dressings available. Which of the following statement(s) is/are true concerning options for surgical dressings? a. Hydrocolloids, such as karaya compounds, offer ... are highly useful in debriding necrotic and fibrous material from wounds and absorbing wound serum

Last Answer : Answer: a, d Although the simplest dressing of gauze and tape combined with the use of antibacterial ointment can achieve moist wound healing in most patients. A multitude of other ... agents have high absorbency for tissue wound fluid and debride necrotic and fibrous material from the wound

Difference between fine powders and granules.

Description : Difference between fine powders and granules.

Last Answer : Fine powder Granules 1. Fine powder does not have free flowing property, hence weight variation in tablet is produced. 1.Granules flow easily and do not give weight variation in the tablet ... die cavity during compression. 4. Granules being heavier do not blow out of die cavity.

Which of the following mineral dressing operations is termed as 'comminution'? (A) Panning (B) Spiralling (C) Tabling (D) None of these

Description : Which of the following mineral dressing operations is termed as 'comminution'? (A) Panning (B) Spiralling (C) Tabling (D) None of these

Last Answer : (D) None of these

Which of the following is used as base material in Selective laser sintering (SLS)? a.Photopolymer b.Thermoplastics, Metal powders c.Titanium alloys d.Various materials

Description : Which of the following is used as base material in Selective laser sintering (SLS)? a.Photopolymer b.Thermoplastics, Metal powders c.Titanium alloys d.Various materials

Last Answer : b.Thermoplastics, Metal powders

Hamzah needs to email a large file to a classmate. Why might he need to use file compression to do so? A. Email services often only let you send compressed data files. B. Compressed files are less likely to become corrupted when being transferred via email. C. He won't need to. All email providers let you send any files you like, regardless of size. D. Email services often have maximum file sizes that prevent you sending files that are too large.

Description : Hamzah needs to email a large file to a classmate. Why might he need to use file compression to do so? A. Email services often only let you send compressed data files. B. Compressed files are ... . D. Email services often have maximum file sizes that prevent you sending files that are too large.

Last Answer : D. Email services often have maximum file sizes that prevent you sending files that are too large.

The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Description : The main size reduction operation in ultrafine grinders is (A) Cutting (B) Attrition (C) Compression (D) Impact

Last Answer : (B) Attrition

Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Description : Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Last Answer : (A) Rod mills

Colloid mills achieve size reduction mainly by (A) Impact (B) Attrition (C) Cutting (D) Compression

Description : Colloid mills achieve size reduction mainly by (A) Impact (B) Attrition (C) Cutting (D) Compression

Last Answer : (B) Attrition

Size reduction mechanism used in Jaw crushers is (A) Attrition (B) Compression

Description : Size reduction mechanism used in Jaw crushers is (A) Attrition (B) Compression

Last Answer : (B) Compression

Maximum size reduction in a fluid energy mill is achieved by (A) Compression (B) Interparticle attrition (C) Cutting (D) Impact

Description : Maximum size reduction in a fluid energy mill is achieved by (A) Compression (B) Interparticle attrition (C) Cutting (D) Impact

Last Answer : (B) Interparticle attrition

Maximum size reduction in a ball mill is done by the, __________ action. (A) Attrition (B) Compression (C) Impact (D) Cutting

Description : Maximum size reduction in a ball mill is done by the, __________ action. (A) Attrition (B) Compression (C) Impact (D) Cutting

Last Answer : (C) Impact

Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one(B) There are only four methods namely compression, impact, attrition andcutting, which the size reduction equipments employ(C) Cutting machines mainly employ 'attrition' for size reduction of solids(D) Operating principles of Dodge and Blake jaw crushers are combined inthe working of universal jaw crushers

Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers

Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids

Toothed roll crushers achieve size reduction by (A) Tearing (shear) and compression (B) Impact and attrition (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Toothed roll crushers achieve size reduction by (A) Tearing (shear) and compression (B) Impact and attrition (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Description : In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Last Answer : (C) Fine

In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Last Answer : (B) Secondary

In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Last Answer : (C) Primary

To avoid fire by spontaneous combustion of coal due to its low temperature oxidation, it should be stored in (A) Shallow and small piles (B) Fine sizes without the presence of any lump (C) Closed space without any ventilation facility (D) Large heaps with small surface to volume ratio

Description : To avoid fire by spontaneous combustion of coal due to its low temperature oxidation, it should be stored in (A) Shallow and small piles (B) Fine sizes without the presence of any lump (C) Closed space without any ventilation facility (D) Large heaps with small surface to volume ratio

Last Answer : (A) Shallow and small piles

Presence of force moisture in coal is most disadvantageous during its (A) Transportation and handling (B) Washing (C) Pulverisation (D) Storage

Description : Presence of force moisture in coal is most disadvantageous during its (A) Transportation and handling (B) Washing (C) Pulverisation (D) Storage

Last Answer : (C) Pulverisation

Presence of free moisture in coal is most disadvantageous during(A) Its pulverisation (as it requires more power) (B) Combustion of fire slacks on the grates (C) Handling (e.g. when emptying wagons) (D) None of these

Description : Presence of free moisture in coal is most disadvantageous during (A) Its pulverisation (as it requires more power) (B) Combustion of fire slacks on the grates (C) Handling (e.g. when emptying wagons) (D) None of these

Last Answer : (A) Its pulverisation (as it requires more power)

Bucket elevators are not suitable for the vertical lifting of __________ materials. (A) Fine (e.g. - 200 mesh size coal) (B) Sticky (e.g. clay paste) (C) Small lumpy (e.g. grains and sand) (D) Free flowing

Description : Bucket elevators are not suitable for the vertical lifting of __________ materials. (A) Fine (e.g. - 200 mesh size coal) (B) Sticky (e.g. clay paste) (C) Small lumpy (e.g. grains and sand) (D) Free flowing

Last Answer : (B) Sticky (e.g. clay paste

Processing of a data file to reduce its size for storage on disk is termed : (1) Amplification (2) Reduction (3) Compression (4) Rarefaction

Description : Processing of a data file to reduce its size for storage on disk is termed : (1) Amplification (2) Reduction (3) Compression (4) Rarefaction

Last Answer : Compression

Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not exceed 4 (C) Both the rolls run necessarily at the same speed (D) Reduction ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Last Answer : (C) Both the rolls run necessarily at the same speed

Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of materials (C) Size enlargement (opposite of size reduction) is not a mechanical operation (D) A 'dust catcher' is simply an enlargement in a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Description : Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of ... a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Last Answer : (C) Size enlargement (opposite of size reduction) is not a mechanical operation

Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the(A) Blake jaw crusher(B) Cage mill(C) Stamp mill(D) Bradford's breaker

Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker

Last Answer : (B) Cage mill

Which of the following is a benefit of lossy compression over lossless? A. File sizes will always be reduced, even when compressed multiple times. B. File quality is not harmed, e.g. images will look exactly the same. C. Files can be decompressed back to their original uncompressed form. D. File sizes are usually significantly smaller.

Description : Which of the following is a benefit of lossy compression over lossless? A. File sizes will always be reduced, even when compressed multiple times. B. File quality is not harmed, e.g. ... can be decompressed back to their original uncompressed form. D. File sizes are usually significantly smaller.

Last Answer : C. Files can be decompressed back to their original uncompressed form.

The purpose of data compression is to decrease file sizes . A. True B. False

Description : The purpose of data compression is to decrease file sizes . A. True B. False

Last Answer : A. True

Index number expressing the relative sizes of both coarse and fine aggregates, is called (A) Proportioning of aggregates (B) Fineness modulus (C) Grading of aggregates (D) None of these

Description : Index number expressing the relative sizes of both coarse and fine aggregates, is called (A) Proportioning of aggregates (B) Fineness modulus (C) Grading of aggregates (D) None of these

Last Answer : Answer: Option B

The movement of soil across a tool surface without sticking is called as a. Pulverisation b. Inversion c. Scouring d. Turning

Description : The movement of soil across a tool surface without sticking is called as a. Pulverisation b. Inversion c. Scouring d. Turning

Last Answer : c. Scouring

Vertical section of plough influence A. Pulverisation B. Depth of cut C. Width of cut. D. Direction of pull

Description : Vertical section of plough influence A. Pulverisation B. Depth of cut C. Width of cut. D. Direction of pull

Last Answer : Pulverisation 

Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Description : Curved twisted blades are specially suited for m. Minimum tillage of trashy land at shallow depths n. Dried hard soils o. Cutting and pulverisation in wet sticky clay soil p. For operating on the sides of plant bed

Last Answer : p. For operating on the sides of plant bed

shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Description : shaped blades are best suited for i. Minimum tillage of trashy land at shallow depths j. Dried hard soils k. Cutting and pulverisation in wet sticky clay soil l. Working under normal field conditions

Last Answer : i. Minimum tillage of trashy land at shallow depths

Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Description : Hook type blades best suited for e. Minimum tillage of trashy land at shallow depths f. Dried hard soils g. Cutting and pulverisation especially in wet sticky clay soil h. Working under normal field conditions

Last Answer : f. Dried hard soils

The amount of energy required to produce a given degree of pulverisation depends primarily on a) Soil strength b) Energy utilisation efficiency of tool c) Both (a) and (b) d) None of the above

Description : The amount of energy required to produce a given degree of pulverisation depends primarily on a) Soil strength b) Energy utilisation efficiency of tool c) Both (a) and (b) d) None of the above

Last Answer : c) Both (a) and (b)

_________means movement of soils across a tool surface without sticking first to avoid soil build ups a) Pulverisation b) Inversion c) Scouring d) Turning

Description : _________means movement of soils across a tool surface without sticking first to avoid soil build ups a) Pulverisation b) Inversion c) Scouring d) Turning

Last Answer : c) Scouring

Separation of materials of the same density based on their sizes by using then-different rates of flow is called (A) Sorting (B) Sizing (C) Flocculation (D) Elutriation

Description : Separation of materials of the same density based on their sizes by using then-different rates of flow is called (A) Sorting (B) Sizing (C) Flocculation (D) Elutriation

Last Answer : (B) Sizing

__________ are mixed using ribbon blenders. (A) Lumpy solids and low viscosity liquids (B) Dry powders (C) High viscosity liquids (D) Thick pastes

Description : __________ are mixed using ribbon blenders. (A) Lumpy solids and low viscosity liquids (B) Dry powders (C) High viscosity liquids (D) Thick pastes

Last Answer : (B) Dry powders

What is a good method of analyzing powders for composition?

Description : What is a good method of analyzing powders for composition?

Last Answer : A method known as Fourier transform-infrared (FT-IR) spectroscopy is often used for this purpose. FT-IR sends light beams of varying wavelength through the sample and the reflected light is ... and the sample composition can be calculated. Analect Instruments Inc. specializes in FT-IR measurement.

Benefits of Waste Heat Recovery a. Reduction in pollution b. Reduction in equipment sizes c. Reduction in auxiliary energy consumption d. All of the above

Description : Benefits of Waste Heat Recovery a. Reduction in pollution b. Reduction in equipment sizes c. Reduction in auxiliary energy consumption d. All of the above

Last Answer : Ans:- d. All of the above

For coarse reduction of hard solids, use (A) Impact (B) Attrition (C) Compression (D) Cutting

Description : For coarse reduction of hard solids, use (A) Impact (B) Attrition (C) Compression (D) Cutting

Last Answer : (C) Compression

The reduction ratio for fine grinders is (A) 5-10 (B) 10-20 (C) 20-40 (D) As high as 100

Description : The reduction ratio for fine grinders is (A) 5-10 (B) 10-20 (C) 20-40 (D) As high as 100

Last Answer : (D) As high as 100

Why are protein powders so expensive?

Description : Why are protein powders so expensive?

Last Answer : I can always find a big container of some for about $15. I don’t think that’s too bad.

Do you think "greens" powders are good for you?

Description : Do you think "greens" powders are good for you?

Last Answer : Amazing Grass is an excellent choice. Just make sure you aren’t allergic to chlorophyll like I am

Which of the following RP technologies uses powders as the starting material? a.Droplet Deposition Manufacturing b.Fused-Deposition Modeling c.Selective Laser Sintering d.Stereolithography

Description : Which of the following RP technologies uses powders as the starting material? a.Droplet Deposition Manufacturing b.Fused-Deposition Modeling c.Selective Laser Sintering d.Stereolithography

Last Answer : c.Selective Laser Sintering

Which of the following is used as base material in Stereolithography (SLA) process? a.Thermoplastics , Metals powders b.Thermoplastics , Eutectic metals. c.Titanium alloys d.Photopolymer

Description : Which of the following is used as base material in Stereolithography (SLA) process? a.Thermoplastics , Metals powders b.Thermoplastics , Eutectic metals. c.Titanium alloys d.Photopolymer

Last Answer : d.Photopolymer

Do only powders dissolve?

Description : Do only powders dissolve?

Last Answer : No a lot of solids do too.

The tinea infections of the human skin are a. All caused by fungi. b. Transmissible from pets. c. Treated with a variety of powders or ointments. d. All the above (a-c) are true.

Description : The tinea infections of the human skin are a. All caused by fungi. b. Transmissible from pets. c. Treated with a variety of powders or ointments. d. All the above (a-c) are true.

Last Answer : d. All the above (a-c) are true.