When does the first segment of the take-off climb begin? a. When V2 is reached b. When 35 feet is reached c. When flaps are up d. When gear and flaps are up

When does the first segment of the take-off climb begin?  
a. When V2 is reached  
b. When 35 feet is reached  
c. When flaps are up  
d. When gear and flaps are up
by

1 Answer

Answer :

b. When 35 feet is reached
by

Related questions

When does the first segment of the take-off climb begin? a. When V2 is reached b. When 35 feet is reached c. When flaps are up d. When gear and flaps are up

Description : When does the first segment of the take-off climb begin? a. When V2 is reached b. When 35 feet is reached c. When flaps are up d. When gear and flaps are up

Last Answer : c. The estimated off-block time

To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb speed (Vx) c. Flaps retracted and at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Description : To give the best obstacle clearance on take-off, take-off should be made with: a. Flaps partially extended and at best rate of climb speed (Vy) b. Flaps partially extended and at best angle of climb ... at best rate of climb speed (Vy) d. Flaps retracted and at best angle of climb speed (Vx)

Last Answer : d. Flaps retracted and at best angle of climb speed (Vx)

The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce the approach angle to 1.5deg (150ft/mile), add 15kts to all speeds, keep the aeroplane clean (no flaps or gear) and fly it into the surface c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Description : The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce ... d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Last Answer : c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first

If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Description : If flaps are lowered during the take-off run: a. The lift would not change until the aircraft is airborne b. The lift would increase when the flaps are lowered c. The lift would decrease d. The acceleration would increase

Last Answer : b. The lift would increase when the flaps are lowered

When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Description : When is spark plug fouling most likely to occur? a. In the climb if you have not adjusted the mixture b. Cruise power c. In the descent if you have not adjusted the mixture d. Max take-off power

Last Answer : a. In the climb if you have not adjusted the mixture

When does the first segment of the take-off climb begin?

Description : When does the first segment of the take-off climb begin?

Last Answer : When 35 feet is reached

If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Description : If a landing is to be made without flaps, the landing speed must be: a. reduced b. increased c. the same as for landing with flaps d. the same as for landing with flaps but with a steeper approach

Last Answer : b. increased

The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Description : The control surface which gives longitudinal control is: a. The rudder b. The ailerons c. The elevators d. The flaps

Last Answer : c. The elevators

Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Description : Which of the following increases the stall angle? a. Slats b. Flaps c. Spoilers d. Ailerons

Last Answer : a. Slats

What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Description : What is the effect of deploying leading edge flaps? a. Increased minimum glide angle b. Decreased minimum glide angle c. Increased glide range d. Decreased sink rate

Last Answer : d. Decreased sink rate

Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Description : Lowering the flaps during a landing approach: a. Increases the angle of descent without increasing the airspeed b. Decreases the angle of descent without increasing power c. Eliminates floating d. Permits approaches at a higher indicated airspeed

Last Answer : a. Increases the angle of descent without increasing the airspeed

A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Description : A hand pump is usually fitted: a. For ground servicing purposes b. Lowering the landing gear in an emergency c. Pressurising the oleo struts in the air d. Retracting the gear after take-off

Last Answer : a. For ground servicing purposes

By what percentage should V2 be greater than VMCA? a. 30% b. 10% c. 20% d. 15%

Description : By what percentage should V2 be greater than VMCA? a. 30% b. 10% c. 20% d. 15%

Last Answer : b. 10%

A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Description : A constant rate of climb in an aeroplane is determined by: a. Wind speed b. The aircraft weight c. Excess engine power d. Excess airspeed

Last Answer : c. Excess engine power

In the event of an act of unlawful interference, which of the following is the correct procedure to be taken by the pilot in command? a. Squawk 7700 if the situation requires and continue the flight as per the ATC clearance received if possible b. Squawk 7500 and broadcast a warning to ATC other traffic on 121.500MHz or the frequency in use whilst maintaining the flight as cleared c. Squawk 7500 (or 7700 if required) and broadcast a warning if the situation forces deviation from the cleared flight plan d. If forced to deviate from the flight plan, climb or descend to altitudes that differ from the normal cruising altitudes by 1000ft

Description : In the event of an act of unlawful interference, which of the following is the correct procedure to be taken by the pilot in command? a. Squawk 7700 if the situation requires and continue ... the flight plan, climb or descend to altitudes that differ from the normal cruising altitudes by 1000ft

Last Answer : c. Squawk 7500 (or 7700 if required) and broadcast a warning if the situation forces deviation from the cleared flight plan

From a pre-flight briefing you know a jet stream is at 31,000ft whilst you are at FL270. You experience moderate CAT. What would be the best course of action? a. Stay level b. Descend c. Climb d. Reduce speed

Description : From a pre-flight briefing you know a jet stream is at 31,000ft whilst you are at FL270. You experience moderate CAT. What would be the best course of action? a. Stay level b. Descend c. Climb d. Reduce speed

Last Answer : b. Descend

Maximum endurance: a. Can be achieved in level unaccelerated flight with minimum fuel consumption b. Can be achieved by flying at the best rate of climb speed in straight and level flight c. Can be achieved in a steady climb d. Can be achieved by flying at the absolute ceiling

Description : Maximum endurance: a. Can be achieved in level unaccelerated flight with minimum fuel consumption b. Can be achieved by flying at the best rate of climb speed in straight and level flight c. Can be achieved in a steady climb d. Can be achieved by flying at the absolute ceiling

Last Answer : a. Can be achieved in level unaccelerated flight with minimum fuel consumption

An aircraft climbs from an airfield, elevation 1500ft, QNH 1023mb, to FL75. What height does the aircraft have to climb? (Assume 1mb=30ft) a. 6600 ft b. 7800 ft c. 6300 ft d. 6000 ft

Description : An aircraft climbs from an airfield, elevation 1500ft, QNH 1023mb, to FL75. What height does the aircraft have to climb? (Assume 1mb=30ft) a. 6600 ft b. 7800 ft c. 6300 ft d. 6000 ft

Last Answer : c. 6300 ft

The transition of altitude to flight level and vice versa is made: a. On the transition level in the climb and transition altitude in the descent b. At the transition altitude in the climb and transition level in the descent c. At the transition level only d. At the transition altitude only

Description : The transition of altitude to flight level and vice versa is made: a. On the transition level in the climb and transition altitude in the descent b. At the transition altitude in the climb and transition level in the descent c. At the transition level only d. At the transition altitude only

Last Answer : b. At the transition altitude in the climb and transition level in the descent

If cabin pressure is decreasing, the cabin VSI will indicate: a. Zero b. Climb c. Descent d. Reducing pressure

Description : If cabin pressure is decreasing, the cabin VSI will indicate: a. Zero b. Climb c. Descent d. Reducing pressure

Last Answer : b. Climb

When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Description : When entering a steep turn, an IVSI is likely to show: a. No change in altitude b. A slight climb c. A slight descent d. A slight descent at high airspeed only

Last Answer : b. A slight climb

A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the inversion is 090/30. What is the safest departure procedure? a. Take-off is not possible under these conditions b. Depart on runway 09 with a tailwind c. Depart runway 27 with maximum throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Description : A flight is to depart from an airport with runway 09 and 27. Surface wind is 270/05; an inversion is reported at 300 feet with turbulence and wind shear. The wind just above the ... throttle during the passage through the inversion d. Depart runway 27 with as steep an ascent as possible

Last Answer : b. Depart on runway 09 with a tailwind

A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Description : A shuttle valve will: a. Allow the accumulator to be emptied after engine shut down b. Reduce pump loading when normal system pressure is reached c. Automatically switched to a more appropriate source of hydraulic supply d. Operate on a rising pressure, higher than the Full Flow relief valve

Last Answer : c. Automatically switched to a more appropriate source of hydraulic supply

When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Description : When would the negative differential limits be reached/exceeded? a. Rapid descent when AC descends below cabin altitude b. During ground pressure testing c. Rapid ascent when aircraft climbs d. When changing to manual operation

Last Answer : a. Rapid descent when AC descends below cabin altitude

What do three green lights represent when the landing gear is selected down? a. The gear is down b. The gear is down and locked c. The gear and doors are down and locked d. The gear is travelling between up and down

Description : What do three green lights represent when the landing gear is selected down? a. The gear is down b. The gear is down and locked c. The gear and doors are down and locked d. The gear is travelling between up and down

Last Answer : b. The gear is down and locked

A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to caster freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Description : A nose wheel control system a. Prevents the nosewheel from castering at all times b. Allows the nosewheel to caster within preset limits about the neutral position c. Allows the nosewheel to ... freely at all times d. Prevents the nose gear from lowering if the nosewheels are not centralised

Last Answer : b. Allows the nosewheel to caster within preset limits about the neutral position

A flight is planned from L to M, distance 850 nm. Wind component out is 35 kt(TWC), TAS 450kt. Mean fuel flow out is 2500kg/hr, mean fuel flow inbound is 1900kg/hr and the fuel available is 6000kg. The time and distance to PSR is: a. 1hr 30 min, 660nm b. 1hr 30 min, 616nm c. 1hr 15 min, 606nm d. 1hr 16 min, 616nm

Description : A flight is planned from L to M, distance 850 nm. Wind component out is 35 kt(TWC), TAS 450kt. Mean fuel flow out is 2500kg/hr, mean fuel flow inbound is 1900kg/hr and the fuel available is 6000kg. The time ... 30 min, 660nm b. 1hr 30 min, 616nm c. 1hr 15 min, 606nm d. 1hr 16 min, 616nm

Last Answer : d. 1hr 16 min, 616nm

At a fuel check you have 60 US gallons (USG) of usable fuel remaining. Alternative fuel required is 12USG. The flight time remaining is 1 hour 35 mins. What is the highest consumption rate acceptable? a. 33.0 USG/Hr b. 37.9 USG/Hr c. 30.3 USG/Hr d. 21.3 USG/Hr

Description : At a fuel check you have 60 US gallons (USG) of usable fuel remaining. Alternative fuel required is 12USG. The flight time remaining is 1 hour 35 mins. What is the highest consumption rate acceptable? a. 33.0 USG/Hr b. 37.9 USG/Hr c. 30.3 USG/Hr d. 21.3 USG/Hr

Last Answer : c. 30.3 USG/Hr

What is the time of useful consciousness at 20,000 feet (moderate activity)? a. 5 minutes b. 1 minute c. 10 minutes d. 30 seconds

Description : What is the time of useful consciousness at 20,000 feet (moderate activity)? a. 5 minutes b. 1 minute c. 10 minutes d. 30 seconds

Last Answer : a. 5 minutes

The Vertical Separation Minimum (VSM) for flights in accordance with IFR within controlled airspace below FL290 is: a. 500 feet (150m) b. 2500 feet (750 m) c. 1000 feet (300m) d. 2000 feet (600m)

Description : The Vertical Separation Minimum (VSM) for flights in accordance with IFR within controlled airspace below FL290 is: a. 500 feet (150m) b. 2500 feet (750 m) c. 1000 feet (300m) d. 2000 feet (600m)

Last Answer : c. 1000 feet (300m)

What is the rule concerning level or height the aircraft should maintain when flying IFR outside controlled airspace unless otherwise directed? a. 2,000 feet above the highest obstacle within 8kms of the heading b. 1,000 feet above the highest obstacle within 8kms of the estimated position of the aircraft c. 1,000 feet above the highest obstacle within 8kms of the planned track d. 2,000 feet above the highest obstacle within 8kms of the planned track

Description : What is the rule concerning level or height the aircraft should maintain when flying IFR outside controlled airspace unless otherwise directed? a. 2,000 feet above the highest obstacle within 8kms of ... planned track d. 2,000 feet above the highest obstacle within 8kms of the planned track

Last Answer : b. 1,000 feet above the highest obstacle within 8kms of the estimated position of the aircraft

Except when cleared by an ATC unit, a VFR flight cannot enter or leave a Control Zone when the cloud base is lower than: a. 1000 feet and less than 8km visibility b. 2000 feet and less than 5km visibility c. 1500 feet or less than 5km visibility d. 1000 feet and less than 5km visibility

Description : Except when cleared by an ATC unit, a VFR flight cannot enter or leave a Control Zone when the cloud base is lower than: a. 1000 feet and less than 8km visibility b. 2000 feet and less than 5km visibility c. 1500 feet or less than 5km visibility d. 1000 feet and less than 5km visibility

Last Answer : c. 1500 feet or less than 5km visibility

Three mountain climbers paid a lot of money to be the first to scale a mountain. After several days of climbing they finally reached the pinnacle, and to their dismay, found a cabin and three frozen bodies. Since the mountain climbers were the first to ever climb the summit, how could this be possible? -Riddles

Description : Three mountain climbers paid a lot of money to be the first to scale a mountain. After several days of climbing they finally reached the pinnacle, and to their dismay, found a cabin and three ... the mountain climbers were the first to ever climb the summit, how could this be possible? -Riddles

Last Answer : They found a cabin of an airplane that had crashed there with 3 bodies in it.

Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what and what should you do? a. Marked temperature drop; apply full power b. Loss of head wind or an increase in tail wind; apply full power c. Incipient engine failure (ignore instruments); lower the nose to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Description : Shortly after take-off, the altitude of the aeroplane suffers an abrupt pitch-up and IAS rapidly decreases followed quickly by a decrease in altitude. Engine indications are normal. You should suspect what ... to gain airspeed d. Local clear air turbulence; reduce speed to VRA and ride it out

Last Answer : b. Loss of head wind or an increase in tail wind; apply full power

When does a pilot apply the limitations of the MEL? a. At parking before commencement of taxi b. Prior to take-off c. At any time in flight d. Any time up to coming to a complete stop and applying the parking brake

Description : When does a pilot apply the limitations of the MEL? a. At parking before commencement of taxi b. Prior to take-off c. At any time in flight d. Any time up to coming to a complete stop and applying the parking brake

Last Answer : d. Any time up to coming to a complete stop and applying the parking brake

For a flight plan filed before flight, the indicated time of departure is: a. The time overhead the first reporting point after take-off b. The time at which the flight plan is filed c. The estimated off-block time d. The time of take-off

Description : For a flight plan filed before flight, the indicated time of departure is: a. The time overhead the first reporting point after take-off b. The time at which the flight plan is filed c. The estimated off-block time d. The time of take-off

Last Answer : c. The estimated off-block time

To act as co-pilot for take-off or landing, you must have: a. Acted as PIC or co-pilot on type in the last 90 days b. Acted as PIC or co-pilot on type in the last 30 days c. Acted as PIC or co-pilot on type in the last 60 days d. Been at the controls for landing in the same type recently

Description : To act as co-pilot for take-off or landing, you must have: a. Acted as PIC or co-pilot on type in the last 90 days b. Acted as PIC or co-pilot on type in the last 30 days c. Acted as PIC or co-pilot on type in the last 60 days d. Been at the controls for landing in the same type recently

Last Answer : a. Acted as PIC or co-pilot on type in the last 90 days

The FMC position will be at its most inaccurate: a. On take-off b. At TOC c. At TOD d. On final approach

Description : The FMC position will be at its most inaccurate: a. On take-off b. At TOC c. At TOD d. On final approach

Last Answer : c. At TOD

DOM 33,510kt; Traffic load 7,600kg; Trip fuel 2040kg; Final reserve 983kg Alternative fuel 1100kg; Contingency 5% of trip fuel Which of the following is correct? a. Estimated landing mass at destination 43,193kg b. Estimated landing mass at destination 43,295kg c. Estimated take-off mass 43,295kg d. Estimated take-off mass 45,233kg

Description : DOM 33,510kt; Traffic load 7,600kg; Trip fuel 2040kg; Final reserve 983kg Alternative fuel 1100kg; Contingency 5% of trip fuel Which of the following is correct? a. Estimated landing mass at destination ... 43,295kg c. Estimated take-off mass 43,295kg d. Estimated take-off mass 45,233kg

Last Answer : b. Estimated landing mass at destination 43,295kg

Refer to CAP697 MRJT1 Fig. 4.2 & 4.5.3.2 Estimated take-off mass 57,000kg; ground distance 150nm; temperature ISA -10C; cruise at M0.74. What is the optimum cruise altitude and TAS? a. 25,000ft & 445kt b. 33,000ft & 420kt c. 25,000ft & 435kt d. 33,000ft & 430kt

Description : Refer to CAP697 MRJT1 Fig. 4.2 & 4.5.3.2 Estimated take-off mass 57,000kg; ground distance 150nm; temperature ISA -10C; cruise at M0.74. What is the optimum cruise altitude and TAS? a. 25,000ft & 445kt b. 33,000ft & 420kt c. 25,000ft & 435kt d. 33,000ft & 430kt

Last Answer : c. 25,000ft & 435kt

For take-off performance calculations, what is taken into account? a. OAT, pressure altitude, wind, weight b. Standard temperature, altitude, wind, weight c. Standard altitude, standard temperature, wind, weight d. Standard temperature, pressure altitude, wind, weight

Description : For take-off performance calculations, what is taken into account? a. OAT, pressure altitude, wind, weight b. Standard temperature, altitude, wind, weight c. Standard altitude, standard temperature, wind, weight d. Standard temperature, pressure altitude, wind, weight

Last Answer : a. OAT, pressure altitude, wind, weight

What is the Total Elapsed Time on a VFR flight plan? a. From take-off to overhead destination b. From take-off to overhead destination + 15 mins c. From take-off to landing d. From taxi to arrival on the gate

Description : What is the Total Elapsed Time on a VFR flight plan? a. From take-off to overhead destination b. From take-off to overhead destination + 15 mins c. From take-off to landing d. From taxi to arrival on the gate

Last Answer : a. From take-off to overhead destination

If a jet engine fails during take-off before V1: a. The take-off can be continued or aborted b. The take-off should be aborted c. The take-off should be continued d. The take-off may be continued if the aircraft speed is above VMCG and lies between VGO and VSTOP

Description : If a jet engine fails during take-off before V1: a. The take-off can be continued or aborted b. The take-off should be aborted c. The take-off should be continued d. The take-off may be continued if the aircraft speed is above VMCG and lies between VGO and VSTOP

Last Answer : b. The take-off should be aborted

What minimum ground visibility is required to enable a SVFR flight to take off from an aerodrome in a CTR? a. 1000m b. 1500m c. 2000m d. 3000m

Description : What minimum ground visibility is required to enable a SVFR flight to take off from an aerodrome in a CTR? a. 1000m b. 1500m c. 2000m d. 3000m

Last Answer : b. 1500m

For a turbojet aeroplane the third segment of climb begins when:

Description : For a turbojet aeroplane the third segment of climb begins when:

Last Answer : Acceleration to a flap retraction speed begins (min 400ft)

For a turbojet aeroplane the second segment of the climb begins when:

Description : For a turbojet aeroplane the second segment of the climb begins when:

Last Answer : Landing gear is fully retracted

Where a light or medium category aeroplane is taking off behind a heavy category aeroplane on the same runway and from the same point, the minimum separation spacing in minutes is: a. 1 b. 2 c. 3 d. 4

Description : Where a light or medium category aeroplane is taking off behind a heavy category aeroplane on the same runway and from the same point, the minimum separation spacing in minutes is: a. 1 b. 2 c. 3 d. 4

Last Answer : b. 2

At a range of 200nm from a VOR, if there is an error of 1°, how far off the centreline is the aircraft? a. 3.5nm b. 1.75nm c. 7nm d. 1nm

Description : At a range of 200nm from a VOR, if there is an error of 1°, how far off the centreline is the aircraft? a. 3.5nm b. 1.75nm c. 7nm d. 1nm

Last Answer : a. 3.5nm

Which of the following would give the best indication of speed? a. A VOR on the flight plan route b. A VOR off the flight plan route c. A DME on the flight plan route d. A DME off the flight plan route

Description : Which of the following would give the best indication of speed? a. A VOR on the flight plan route b. A VOR off the flight plan route c. A DME on the flight plan route d. A DME off the flight plan route

Last Answer : c. A DME on the flight plan route