Which interrupt has the highest priority? a) INTR b) TRAP c) RST6.5

Which interrupt has the highest priority?  
a) INTR b) TRAP c) RST6.5
by

1 Answer

Answer :

c) RST6.5
by

Related questions

Which of the following is hardware interrupts? a) RST5.5, RST6.5, RST7.5 b) INTR, TRAP c) a & b

Description : Which of the following is hardware interrupts? a) RST5.5, RST6.5, RST7.5 b) INTR, TRAP c) a & b

Last Answer : c) a & b

Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR

Description : Which of the following 8085 microprocessor hardware interrupt has the lowest priority? (A) RST 6.5 (B) RST 7.5 (C) TRAP (D) INTR 

Last Answer : Answer: D

In 8086, Example for Non maskable interrupts are a) Trapb) RST6.5 c) INTR

Description : In 8086, Example for Non maskable interrupts are a) Trapb) RST6.5 c) INTR

Last Answer : a) Trap

Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Description : Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Last Answer : b) RST7.5 is a raising edge-trigging interrupt.

What are software interrupts? a) RST 0 - 7 b) RST 5.5 - 7.5 c) INTR, TRAP

Description : What are software interrupts? a) RST 0 - 7 b) RST 5.5 - 7.5 c) INTR, TRAP

Last Answer : a) RST 0

In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Description : In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Last Answer : a)IE1

In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Description : In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Last Answer : c)IE0

What are level Triggering interrupts? a) INTR&TRAP b)RST6.5&RST5.5 c)RST7.5&RST6.5

Description : What are level Triggering interrupts? a) INTR&TRAP b)RST6.5&RST5.5 c)RST7.5&RST6.5

Last Answer : b)RST6.5&RST5.5

If you are to use [Control-c] as the interrupt key instead of [Del], then you will have to use A. tty ^c B. stty intr \^c C. stty echoe D. stty echo \^a E. None of the above

Description : If you are to use [Control-c] as the interrupt key instead of [Del], then you will have to use A. tty ^c B. stty intr \^c C. stty echoe D. stty echo \^a E. None of the above

Last Answer : B. stty intr \^c

n 8086 microprocessor the following has the highest priority among all type interrupts. a) NMI b) DIV 0 c) TYPE 255 d) OVER FLOW

Description : n 8086 microprocessor the following has the highest priority among all type interrupts. a) NMI b) DIV 0 c) TYPE 255 d) OVER FLOW

Last Answer : a) NMI

Which Interrupt Has The Highest Priority?

Description : Which Interrupt Has The Highest Priority?

Last Answer : Answer :TRAP has the highest priority.

What is meant by interrupt?

Description : What is meant by interrupt?

Last Answer : Interrupt is an external signal that causes a microprocessor to jump to a specific subroutine.

List the four instructions which control the interrupt structure of the 8085 microprocessor.

Description : List the four instructions which control the interrupt structure of the 8085 microprocessor.

Last Answer : • DI ( Disable Interrupts ) • EI ( Enable Interrupts ) • RIM ( Read Interrupt Masks ) • SIM ( Set Interrupt Masks )

Serial port interrupt is generated, if ____ bits are seta) IE b) RI, IE c) IP, TI d) RI, TI

Description : Serial port interrupt is generated, if ____ bits are seta) IE b) RI, IE c) IP, TI d) RI, TI

Last Answer : d) RI, TI

The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Description : The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Last Answer : a. Interrupt

Which are the flags of status register: a. Over flow flag b. Carry flag c. Half carry flag d. Zero flag e. Interrupt flag f. Negative flag g. All of these

Description : Which are the flags of status register: a. Over flow flag b. Carry flag c. Half carry flag d. Zero flag e. Interrupt flag f. Negative flag g. All of these

Last Answer : g. All of these

The interrupt vector table of 80386 has been allocated ______ space starting from _______ to _______. a) 1Kbyte, 00000H, 003FFH b) 2Kbyte, 10000H, 004FFH c) 3Kbyte, 01000H, 007FFH d) 4Kbyte, 01000H, 009FFH

Description : The interrupt vector table of 80386 has been allocated ______ space starting from _______ to _______. a) 1Kbyte, 00000H, 003FFH b) 2Kbyte, 10000H, 004FFH c) 3Kbyte, 01000H, 007FFH d) 4Kbyte, 01000H, 009FFH

Last Answer : c) 3Kbyte, 01000H, 007FFH

Serial port vector address is of _______. And causes an interrupt when ________. a) 0013H, either TI or RI flag is set b) 0023H, either TI or RI flag is reset c) 0013H, either TI or RI flag is reset d) 0023H, either TI or RI flag is set

Description : Serial port vector address is of _______. And causes an interrupt when ________. a) 0013H, either TI or RI flag is set b) 0023H, either TI or RI flag is reset c) 0013H, either TI or RI flag is reset d) 0023H, either TI or RI flag is set

Last Answer : a) 0013H, either TI or RI flag is set

In 8051 an external interrupt 1 vector address is of ________ and causes of interrupt if ____. a) 000BH, a high to low transition on pin INT1 b) 001BH, a low to high transition on pin INT1 c) 0013H, a high to low transition on pin INT1 d) 0023H, a low to high transition on pin INT1

Description : In 8051 an external interrupt 1 vector address is of ________ and causes of interrupt if ____. a) 000BH, a high to low transition on pin INT1 b) 001BH, a low to high transition on pin INT1 c) 0013H, a high to low transition on pin INT1 d) 0023H, a low to high transition on pin INT1

Last Answer : a) 000BH, a high to low transition on pin INT1

In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Description : In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Last Answer : c) 21, 8

Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Description : Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Last Answer : a) IE

If ______ and ________ connections are made so that an error condition in 8087 can interrupt to the processor. a) BHE, RQ/GT1 b) BUSY, TEST c) INT, NMI d) RQ/GT0, RQ/GT1

Description : If ______ and ________ connections are made so that an error condition in 8087 can interrupt to the processor. a) BHE, RQ/GT1 b) BUSY, TEST c) INT, NMI d) RQ/GT0, RQ/GT1

Last Answer : c) INT, NMI

8086 is interfaced to two 8259s (Programmable interrupt controllers). If 8259s are in master slave configuration the number of interrupts available to the 8086 microprocessor is a) 8 b) 16 c) 15 d) 64

Description : 8086 is interfaced to two 8259s (Programmable interrupt controllers). If 8259s are in master slave configuration the number of interrupts available to the 8086 microprocessor is a) 8 b) 16 c) 15 d) 64

Last Answer : a) 8

In 8279, a scanned sensor matrix mode, if a sensor changes its state, the ___ line goes ____ to interrupt the CPU. a) CS, high b) A0, high c) IRQ, high d) STB, high

Description : In 8279, a scanned sensor matrix mode, if a sensor changes its state, the ___ line goes ____ to interrupt the CPU. a) CS, high b) A0, high c) IRQ, high d) STB, high

Last Answer : c) IRQ, high

In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Description : In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Last Answer : c) 21,

Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Description : Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Last Answer : d) RI, TI

What is meant by Maskable interrupts? a) An interrupt which can never be turned off. b) An interrupt that can be turned off by the programmer. c) none

Description : What is meant by Maskable interrupts? a) An interrupt which can never be turned off. b) An interrupt that can be turned off by the programmer. c) none

Last Answer : b) An interrupt that can be turned off by the programmer.

RIM is used to check whether, ______ a) The write operation is done or not b) The interrupt is Masked or not c) a & b

Description : RIM is used to check whether, ______ a) The write operation is done or not b) The interrupt is Masked or not c) a & b

Last Answer : b) The interrupt is Masked or not

What is SIM? a) Select Interrupt Mask b) Sorting Interrupt Mask c) Set Interrupt Mask.

Description : What is SIM? a) Select Interrupt Mask b) Sorting Interrupt Mask c) Set Interrupt Mask.

Last Answer : c) Set Interrupt Mask.

What is the RST for the TRAP? a) RST5.5 b) RST4.5 c) RST4

Description : What is the RST for the TRAP? a) RST5.5 b) RST4.5 c) RST4

Last Answer : b) RST4.5

Explain priority interrupts of 8085.

Description : Explain priority interrupts of 8085.

Last Answer : The 8085 microprocessor has five interrupt inputs. They are TRAP, RST 7.5, RST 6.5, RST 5.5, and INTR. These interrupts have a fixed priority of interrupt service. If two or more interrupts go ... 8085 is shown in the table. Interrupts Priority TRAP RST 7.5 RST 6.5 RST 5.5 INTR

Vector address of TRAP a) 24H b) 36H c) 24 d) 18H

Description : Vector address of TRAP a) 24H b) 36H c) 24 d) 18H

Last Answer : c) 24

Address line for TRAP is? a) 0023H b) 0024H c) 0033H

Description : Address line for TRAP is? a) 0023H b) 0024H c) 0033H

Last Answer : b) 0024H

Match the following mechanisms for interrupting the execution of a process and their uses. i) Interrupt a) Call to an operating system function ii) Trap b) Reaction to an asynchronous external event iii) Supervisor Call c) Handling of a error or an exception condition A) i-a, ii-b, iii-c B) i-c, ii-a, iii-b C) i-b, ii-c, iii-a D) i-a, ii-c, iii-b

Description : Match the following mechanisms for interrupting the execution of a process and their uses. i) Interrupt a) Call to an operating system function ii) Trap b) Reaction to an asynchronous external event iii) Supervisor Call c) Handling of a error ... -a, iii-b C) i-b, ii-c, iii-a D) i-a, ii-c, iii-b

Last Answer : C) i-b, ii-c, iii-a

What is the vector location of TRAP interrupt?

Description : What is the vector location of TRAP interrupt? (A) 0000 h (B) 0008 h (C) 0014 h (D) 0024 h

Last Answer : What is the vector location of TRAP interrupt?  0024 h

Explain Briefly What Happens When The Intr Signal Goes High In The 8085?

Description : Explain Briefly What Happens When The Intr Signal Goes High In The 8085?

Last Answer : Answer :The INTR is a maskable interrupt for the 8085. It has the lowest priority and is also non vectored. When this INTR signal goes into the high state the following things occur / ... the processor saves the address of new instruction into the STACK and an interrupt service subroutine begins.

What Are The Two Major Differences Between Intr And Other Interrupts ( Hardware)?

Description : What Are The Two Major Differences Between Intr And Other Interrupts ( Hardware)?

Last Answer : Answer :The two major differences between INTR and the other hardware interrupts are as follows:All the hardware interrupts are vectored interrupts but the INTR interrupt is not so. An INTR interrupt will ... saved but in the case of other hardware interrupts the locations is saved in the stack.

Where can I watch the current Olympics online internationally (as in, not in the US)? Highest priority: watching figure skating events in full after they happen.

Description : Where can I watch the current Olympics online internationally (as in, not in the US)? Highest priority: watching figure skating events in full after they happen.

Last Answer : I am not sure if its legal, as I have never used it, but channelsurfing.net seems like the big thing right now.

A project manager has been transferred to a major software development project that is in the implementation phase. The highest priority for this project

Description : A project manager has been transferred to a major software development project that is in the implementation phase. The highest priority for this projectmanager should be to A. Establish a relationship with ... the manager' s management style D. Ensure that the project proceeds at its current pace

Last Answer : B. Learn the project objectives and the existing project plan

The three outputs x1x2x3 from the 8x3 priority encoder are used to provide a vector address of the form 101x1x2x300. What is the second highest priority vector address in hexadecimal if the vector addresses are starting from the one with the highest priority? (A) BC (B) A4 (C) BD (D) AC

Description : The three outputs x1x2x3 from the 8x3 priority encoder are used to provide a vector address of the form 101x1x2x300. What is the second highest priority vector address in hexadecimal if the vector addresses are starting from the one with the highest priority? (A) BC (B) A4 (C) BD (D) AC

Last Answer : Answer: B

How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Description : How many speed of 8088,8085,8086 microprocessor: a. 2.5 Million instruction per second b. 1.5 Million instruction per second c. 3.5 Million instruction per second d. 1.6 Million instruction per second

Last Answer : a. 2.5 Million instruction per second

The number of software interrupts in 8085 is ____ a) 5 b) 8

Description : The number of software interrupts in 8085 is ____ a) 5 b) 8

Last Answer : b) 8

The original ASCII code used…bits of each byte, reserving that last bit for error checking a. 5 b. 6 c. 7 d. 8

Description : The original ASCII code used…bits of each byte, reserving that last bit for error checking a. 5 b. 6 c. 7 d. 8

Last Answer : c. 7

Floppy disks typically in diameter a. 3” b. 5.25” c. 8” d. All of above

Description : Floppy disks typically in diameter a. 3” b. 5.25” c. 8” d. All of above

Last Answer : d. All of above

The capacity of 3.5 inch floppy disk is a. 1.40 MB b. 1.44 GB c. 1.40 GB d. 1.44 MB

Description : The capacity of 3.5 inch floppy disk is a. 1.40 MB b. 1.44 GB c. 1.40 GB d. 1.44 MB

Last Answer : a. 1.40 MB

How many ways of transferring data between the microprocessor and a physical I/O device: a. 2 b. 3 c. 4 d. 5

Description : How many ways of transferring data between the microprocessor and a physical I/O device: a. 2 b. 3 c. 4 d. 5

Last Answer : b. 3

How many parts of dedicated register: a. 2 b. 4 c. 5 d. 6

Description : How many parts of dedicated register: a. 2 b. 4 c. 5 d. 6

Last Answer : c. 5

Interfacing LCD with 89C51 _____ data lines are used along with the _____ signals. a) 6, RS, RW b) 5, RW, EN c) 8, RS, EN, RW d) 9, RS, EN, RW

Description : Interfacing LCD with 89C51 _____ data lines are used along with the _____ signals. a) 6, RS, RW b) 5, RW, EN c) 8, RS, EN, RW d) 9, RS, EN, RW

Last Answer : a) 6, RS, RW

In 8255, under the I/O mode of operation we have __ modes. Under which mode will have the following features i) A 5 bit control port is available. ii) Three I/O lines are available at Port C. a) 3, Mode2 b) 2, Mode 2 c) 4, Mode 3 d) 3, Mode 2

Description : In 8255, under the I/O mode of operation we have __ modes. Under which mode will have the following features i) A 5 bit control port is available. ii) Three I/O lines are available at Port C. a) 3, Mode2 b) 2, Mode 2 c) 4, Mode 3 d) 3, Mode 2

Last Answer : a) 3, Mode2

Explain ALIGN & ASSUME

Description : Explain ALIGN & ASSUME

Last Answer : The ALIGN directive forces the assembler to align the nextsegment at an address divisible by specified divisor. The format is ALIGN number where number can be 2, 4, 8 or 16. Example ALIGN 8. The ASSUME ... the segment registers at execution time. Example ASSUME CS: code, DS: data, SS: stack