The interrupt vector table of 80386 has been allocated ______ space starting from _______ to _______. a) 1Kbyte, 00000H, 003FFH b) 2Kbyte, 10000H, 004FFH c) 3Kbyte, 01000H, 007FFH d) 4Kbyte, 01000H, 009FFH

The interrupt vector table of 80386 has been allocated ______ space starting from _______ to _______.
a) 1Kbyte, 00000H, 003FFH
b) 2Kbyte, 10000H, 004FFH
c) 3Kbyte, 01000H, 007FFH
d) 4Kbyte, 01000H, 009FFH
by

1 Answer

Answer :

c) 3Kbyte, 01000H, 007FFH
by

Related questions

Serial port vector address is of _______. And causes an interrupt when ________. a) 0013H, either TI or RI flag is set b) 0023H, either TI or RI flag is reset c) 0013H, either TI or RI flag is reset d) 0023H, either TI or RI flag is set

Description : Serial port vector address is of _______. And causes an interrupt when ________. a) 0013H, either TI or RI flag is set b) 0023H, either TI or RI flag is reset c) 0013H, either TI or RI flag is reset d) 0023H, either TI or RI flag is set

Last Answer : a) 0013H, either TI or RI flag is set

80386 support which type of descriptor table from the following? a) TDS b) ADS c) GDS d) MDS

Description : 80386 support which type of descriptor table from the following? a) TDS b) ADS c) GDS d) MDS

Last Answer : c) GDS

In 8051 an external interrupt 1 vector address is of ________ and causes of interrupt if ____. a) 000BH, a high to low transition on pin INT1 b) 001BH, a low to high transition on pin INT1 c) 0013H, a high to low transition on pin INT1 d) 0023H, a low to high transition on pin INT1

Description : In 8051 an external interrupt 1 vector address is of ________ and causes of interrupt if ____. a) 000BH, a high to low transition on pin INT1 b) 001BH, a low to high transition on pin INT1 c) 0013H, a high to low transition on pin INT1 d) 0023H, a low to high transition on pin INT1

Last Answer : a) 000BH, a high to low transition on pin INT1

The processor 80386/80486 and the Pentium processor uses _____ bits address bus: a. 16 b. 32 c. 36 d. 64

Description : The processor 80386/80486 and the Pentium processor uses _____ bits address bus: a. 16 b. 32 c. 36 d. 64

Last Answer : b. 32

80386 support overall ___ addressing modes to facilitate efficient execution of higher level language programs. a) 9 b) 10 c) 11 d) 12

Description : 80386 support overall ___ addressing modes to facilitate efficient execution of higher level language programs. a) 9 b) 10 c) 11 d) 12

Last Answer : 11

____is used to control the cache with two new control bits not present in the 80386 microprocessor. What are the bits used to control the 8K byte cache? a) CR0, CD, NW b) CR0, NW, PWT c) Control Register Zero, PWT, PCD d) none

Description : ____is used to control the cache with two new control bits not present in the 80386 microprocessor. What are the bits used to control the 8K byte cache? a) CR0, CD, NW b) CR0, NW, PWT c) Control Register Zero, PWT, PCD d) none

Last Answer : d) none

If ______input pin of 80386 if activated, allows address pipelining during 80386 bus cycles. a) BS16 b) NA c) PEREQ d) ADS

Description : If ______input pin of 80386 if activated, allows address pipelining during 80386 bus cycles. a) BS16 b) NA c) PEREQ d) ADS

Last Answer : a) BS16

The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Description : The external device is connected to a pin called the ______ pin on the processor chip. a. Interrupt b. Transfer c. Both d. None of these

Last Answer : a. Interrupt

If ______ and ________ connections are made so that an error condition in 8087 can interrupt to the processor. a) BHE, RQ/GT1 b) BUSY, TEST c) INT, NMI d) RQ/GT0, RQ/GT1

Description : If ______ and ________ connections are made so that an error condition in 8087 can interrupt to the processor. a) BHE, RQ/GT1 b) BUSY, TEST c) INT, NMI d) RQ/GT0, RQ/GT1

Last Answer : c) INT, NMI

RIM is used to check whether, ______ a) The write operation is done or not b) The interrupt is Masked or not c) a & b

Description : RIM is used to check whether, ______ a) The write operation is done or not b) The interrupt is Masked or not c) a & b

Last Answer : b) The interrupt is Masked or not

In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Description : In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Last Answer : c) 21, 8

In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Description : In 8096 we have _____interrupt sources and _______ interrupt vectors. a) 18, 8 b) 21, 6 c) 21, 8 d) 16, 8

Last Answer : c) 21,

A set of information that defines the status of resources allocated to a process is a. Process control b. ALU c. Register Unit d. Process description

Description : A set of information that defines the status of resources allocated to a process is a. Process control b. ALU c. Register Unit d. Process description

Last Answer : d. Process description

What is meant by interrupt?

Description : What is meant by interrupt?

Last Answer : Interrupt is an external signal that causes a microprocessor to jump to a specific subroutine.

List the four instructions which control the interrupt structure of the 8085 microprocessor.

Description : List the four instructions which control the interrupt structure of the 8085 microprocessor.

Last Answer : • DI ( Disable Interrupts ) • EI ( Enable Interrupts ) • RIM ( Read Interrupt Masks ) • SIM ( Set Interrupt Masks )

Serial port interrupt is generated, if ____ bits are seta) IE b) RI, IE c) IP, TI d) RI, TI

Description : Serial port interrupt is generated, if ____ bits are seta) IE b) RI, IE c) IP, TI d) RI, TI

Last Answer : d) RI, TI

Which are the flags of status register: a. Over flow flag b. Carry flag c. Half carry flag d. Zero flag e. Interrupt flag f. Negative flag g. All of these

Description : Which are the flags of status register: a. Over flow flag b. Carry flag c. Half carry flag d. Zero flag e. Interrupt flag f. Negative flag g. All of these

Last Answer : g. All of these

In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Description : In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Last Answer : a)IE1

Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Description : Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Last Answer : a) IE

8086 is interfaced to two 8259s (Programmable interrupt controllers). If 8259s are in master slave configuration the number of interrupts available to the 8086 microprocessor is a) 8 b) 16 c) 15 d) 64

Description : 8086 is interfaced to two 8259s (Programmable interrupt controllers). If 8259s are in master slave configuration the number of interrupts available to the 8086 microprocessor is a) 8 b) 16 c) 15 d) 64

Last Answer : a) 8

In 8279, a scanned sensor matrix mode, if a sensor changes its state, the ___ line goes ____ to interrupt the CPU. a) CS, high b) A0, high c) IRQ, high d) STB, high

Description : In 8279, a scanned sensor matrix mode, if a sensor changes its state, the ___ line goes ____ to interrupt the CPU. a) CS, high b) A0, high c) IRQ, high d) STB, high

Last Answer : c) IRQ, high

In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Description : In 8051 which interrupt has highest priority? a)IE1 b)TF0 c)IE0 d)TF1

Last Answer : c)IE0

Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Description : Serial port interrupt is generated, if ____ bits are set a) IE b) RI, IE c) IP, TI d) RI, TI

Last Answer : d) RI, TI

What is meant by Maskable interrupts? a) An interrupt which can never be turned off. b) An interrupt that can be turned off by the programmer. c) none

Description : What is meant by Maskable interrupts? a) An interrupt which can never be turned off. b) An interrupt that can be turned off by the programmer. c) none

Last Answer : b) An interrupt that can be turned off by the programmer.

What is SIM? a) Select Interrupt Mask b) Sorting Interrupt Mask c) Set Interrupt Mask.

Description : What is SIM? a) Select Interrupt Mask b) Sorting Interrupt Mask c) Set Interrupt Mask.

Last Answer : c) Set Interrupt Mask.

Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Description : Which interrupt is not level sensitive in 8085? a) RST6.5 is a raising edge-trigging interrupt. b) RST7.5 is a raising edge-trigging interrupt. c) a & b.

Last Answer : b) RST7.5 is a raising edge-trigging interrupt.

Which interrupt has the highest priority? a) INTR b) TRAP c) RST6.5

Description : Which interrupt has the highest priority? a) INTR b) TRAP c) RST6.5

Last Answer : c) RST6.5

The coprocessors operate in ______ with a processor on the same buses and with the same instruction _______. a) Parallel, byte stream. b) Series, byte stream. c) Series, bite stream d) Parallel, bite stream.

Description : The coprocessors operate in ______ with a processor on the same buses and with the same instruction _______. a) Parallel, byte stream. b) Series, byte stream. c) Series, bite stream d) Parallel, bite stream.

Last Answer : a) Parallel, byte stream.

Vector address of TRAP a) 24H b) 36H c) 24 d) 18H

Description : Vector address of TRAP a) 24H b) 36H c) 24 d) 18H

Last Answer : c) 24

What is the vector location of TRAP interrupt?

Description : What is the vector location of TRAP interrupt? (A) 0000 h (B) 0008 h (C) 0014 h (D) 0024 h

Last Answer : What is the vector location of TRAP interrupt?  0024 h

The allocated cells in the transportation table are called .............................. a. Occupied cells b. Empty cells c. Unoccupied cells d. None of these

Description : The allocated cells in the transportation table are called .............................. a. Occupied cells b. Empty cells c. Unoccupied cells d. None of these

Last Answer : a. Occupied cells

The instructions for starting the computer are house on a. Random access memory b. CD-Rom c. Read only memory chip

Description : The instructions for starting the computer are house on a. Random access memory b. CD-Rom c. Read only memory chip

Last Answer : c. Read only memory chip

The process of starting a or restarting a computer system by loading instructions from a secondary storage device into the computer memory is called a. Duping b. Booting c. Padding d. CPS

Description : The process of starting a or restarting a computer system by loading instructions from a secondary storage device into the computer memory is called a. Duping b. Booting c. Padding d. CPS

Last Answer : b. Booting

Which was the world’s first microcomputer that used Intel 80386 microprocessor chip? A) IBM PS/2 B) HP-9830 C) DeskPro-386 D) IBM-360

Description : Which was the world’s first microcomputer that used Intel 80386 microprocessor chip? A) IBM PS/2 B) HP-9830 C) DeskPro-386 D) IBM-360

Last Answer : Answer : C

L2 cache memory is places at ______ a. On Processor b. On Mother Board c. On Memory d. All of these

Description : L2 cache memory is places at ______ a. On Processor b. On Mother Board c. On Memory d. All of these

Last Answer : b. On Mother Board

L1 cache memory is places at ______ a. On Processor b. On Mother Board c. On Memory d. All of these

Description : L1 cache memory is places at ______ a. On Processor b. On Mother Board c. On Memory d. All of these

Last Answer : a. On Processor

For the number A[15:0] = 0110110010001111, A[14:13] is ______ A[3:2]. a. less than b. greater than c. the same as d . cannot be determined

Description : For the number A[15:0] = 0110110010001111, A[14:13] is ______ A[3:2]. a. less than b. greater than c. the same as d . cannot be determined

Last Answer : c. the same as

When the write enable input is not asserted, the gated D latch ______ its output. a. can not change b. clears c. sets d. complements

Description : When the write enable input is not asserted, the gated D latch ______ its output. a. can not change b. clears c. sets d. complements

Last Answer : a. can not change

The problem of bus confect and sparse address distribution are eliminated by the use of ______ address technique: a. Fully decoding b. Half decoding c. Both a & b d. None of these

Description : The problem of bus confect and sparse address distribution are eliminated by the use of ______ address technique: a. Fully decoding b. Half decoding c. Both a & b d. None of these

Last Answer : a. Fully decoding

The external system bus architecture is created using from ______ architecture: a. Pascal b. Dennis Ritchie c. Charles Babbage d. Von Neumann

Description : The external system bus architecture is created using from ______ architecture: a. Pascal b. Dennis Ritchie c. Charles Babbage d. Von Neumann

Last Answer : d. Von Neumann

A new signal group on the 80486 is the ______. a) PARITY b) DP0-DP3 c) PCHK d) all

Description : A new signal group on the 80486 is the ______. a) PARITY b) DP0-DP3 c) PCHK d) all

Last Answer : b) DP0-DP3

ACALL instruction allows specifying ______address in the instruction and calling subroutine within ______ program memory block. a) 2byte, 3K b) 11bit, 2K c) 9bit, 2K d) 1byte, 3K

Description : ACALL instruction allows specifying ______address in the instruction and calling subroutine within ______ program memory block. a) 2byte, 3K b) 11bit, 2K c) 9bit, 2K d) 1byte, 3K

Last Answer : c) 9bit, 2K

8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Description : 8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Last Answer : c) 4, i,ii,iii

Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Description : Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Last Answer : d) 16, MCS96

The SP is of ___ wide register. And this may be defined anywhere in the ______. a) 8 byte, on-chip 128 byte RAM. b) 8 bit, on chip 256 byte RAM. c) 16 bit,

Description : The SP is of ___ wide register. And this may be defined anywhere in the ______. a) 8 byte, on-chip 128 byte RAM. b) 8 bit, on chip 256 byte RAM. c) 16 bit,

Last Answer : a) 8 byte, on-chip 128 byte RAM.

The 8051 microcontroller is of ___pin package as a ______ processor. a) 30, 1byte b) 20, 1 byte c) 40, 8 bit

Description : The 8051 microcontroller is of ___pin package as a ______ processor. a) 30, 1byte b) 20, 1 byte c) 40, 8 bit

Last Answer : c) 40, 8 bit

______ input is available, so that another coprocessor can be connected and function in _________ with the 8087. . a) RQ/GT0, parallel b) RQ/GT1, parallel c) QS1 & QS0, parallel d) S0 & S1, parallel.

Description : ______ input is available, so that another coprocessor can be connected and function in _________ with the 8087. . a) RQ/GT0, parallel b) RQ/GT1, parallel c) QS1 & QS0, parallel d) S0 & S1, parallel.

Last Answer : a) RQ/GT0, parallel

8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Description : 8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Last Answer : c) 4, i,ii,iii

Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Description : Intel 8096 is of ___ bit microcontroller family called as ______. a) 8, MCS51 b) 16, MCS51 c) 8, MCS96 d) 16, MCS96

Last Answer : d) 16, MCS96

The 8051 microcontroller is of ___pin package as a ______ processor. a) 30, 1byte b) 20, 1 byte c) 40, 8 bit d) 40, 8 byte

Description : The 8051 microcontroller is of ___pin package as a ______ processor. a) 30, 1byte b) 20, 1 byte c) 40, 8 bit d) 40, 8 byte

Last Answer : c) 40, 8 bit