The major limitation of metallic recuperated is ------- a) Limitation of handling COx, NOx etc. b) Limitation of reduced life for handling temperature more than 1000 oC c) Manufacturing difficulty of the required design d) None of the above

The major limitation of metallic recuperated is -------
a) Limitation of handling COx, NOx etc.
b) Limitation of reduced life for handling temperature more than 1000 oC
c) Manufacturing difficulty of the required design
d) None of the above
by

1 Answer

Answer :

Limitation of reduced life for handling temperature more than 1000 oC
by

Related questions

What are the components responsible for acid rain? (1) Nitrogen monoxide (NO) and Carbon monoxide (CO) (2) Sulphur dioxide (SO2) and Nitrogen oxides (NOx) (3) Carbon dioxide (CO2) and Carbon monoxide (CO) (4) Oxides of carbon (COx) and Oxides of nitrogen (NOx)

Description : What are the components responsible for acid rain? (1) Nitrogen monoxide (NO) and Carbon monoxide (CO) (2) Sulphur dioxide (SO2) and Nitrogen oxides (NOx) (3) Carbon dioxide (CO2) and Carbon monoxide (CO) (4) Oxides of carbon (COx) and Oxides of nitrogen (NOx)

Last Answer : (2) Sulphur dioxide (SO2) and Nitrogen oxides (NOx) Explanation: Acid rain is caused by emissions of sulfur dioxide (SO2) and nitrogen oxide (NO), which react with the water molecules in the ... in acid rain can cause paint to peel, corrosion of steel structures and weathering of stone buildings.

What are the components responsible for acid rain? (1) Nitrogen monoxide (NO) and Carbon monoxide (CO) (2) Sulphur dioxide (SO2 ) and Nitrogen oxides (NOx ) (3) Carbon dioxide (CO2 ) and Carbon monoxide (CO) (4) Oxides of carbon (COx ) and Oxides of nitrogen (NOx )

Description : What are the components responsible for acid rain? (1) Nitrogen monoxide (NO) and Carbon monoxide (CO) (2) Sulphur dioxide (SO2 ) and Nitrogen oxides (NOx ) (3) Carbon dioxide (CO2 ) and Carbon monoxide (CO) (4) Oxides of carbon (COx ) and Oxides of nitrogen (NOx )

Last Answer : Sulphur dioxide (SO2 ) and Nitrogen oxides (NOx ) 

Recuperated will be more efficient if the flow path of hot and cold fluids is in: a) Co-current mode b) Counter current mode c) Cross current mode d) Cone of the above

Description : Recuperated will be more efficient if the flow path of hot and cold fluids is in: a) Co-current mode b) Counter current mode c) Cross current mode d) Cone of the above

Last Answer : Counter current mode

Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Last Answer : Billet Reheating Furnace

Disadvantage of hydrogen as a fuel in IC engine is a) storage is safe b) low NOx c) detonating tendency d) easy handling

Description : Disadvantage of hydrogen as a fuel in IC engine is a) storage is safe b) low NOx c) detonating tendency d) easy handling

Last Answer : Answer: c Explanation: None.

Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Description : Advantages of fluidised bed combustion are (A) Reduced NOx formation in flue gas (B) Lower furnace operating temperature (C) High heat transfer rate (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Typical waste gases temperature from glass melting furnace a) 1000-1550 oC b) 800-950 oC c) 650–750 oC d) 760-815 oC

Description : Typical waste gases temperature from glass melting furnace a) 1000-1550 oC b) 800-950 oC c) 650–750 oC d) 760-815 oC

Last Answer : 1000-1550 oC

From which of the following is not the main element of Flexible manufacturing system a.Work handling system b.Material handling system c.Tool handling system d.Main frame computer

Description : From which of the following is not the main element of Flexible manufacturing system a.Work handling system b.Material handling system c.Tool handling system d.Main frame computer

Last Answer : a.Work handling system

From the following which is the main components of Flexible manufacturing system(FMS). a.Main frame computer b.Automated guided vehicle c.Material handling system d.All of the above

Description : From the following which is the main components of Flexible manufacturing system(FMS). a.Main frame computer b.Automated guided vehicle c.Material handling system d.All of the above

Last Answer : d.All of the above

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

Heat recovery equipment will be most effective when the temperature of flue gas is: a) 250oC b) 200 oC c)400 oC d) 280 oC

Description : Heat recovery equipment will be most effective when the temperature of flue gas is: a) 250oC b) 200 oC c)400 oC d) 280 oC

Last Answer : 400 oC

Because less coal is consumed in this system, emissions of ______ and particulate and solid waste by products are reduced. a. Sulphur dioxide (SO2) b. Nitrogen oxide (NOx) c. Carbon dioxide (CO2) d. All of the above.

Description : Because less coal is consumed in this system, emissions of ______ and particulate and solid waste by products are reduced. a. Sulphur dioxide (SO2) b. Nitrogen oxide (NOx) c. Carbon dioxide (CO2) d. All of the above.

Last Answer : d. All of the above.

Low NOx Combustion Technology Regulation in Japan for Coal Firing Boiler has reduced from 400 ppm to____ a. 100ppm b. 200ppm c. 300ppm d. 400ppm

Description : Low NOx Combustion Technology Regulation in Japan for Coal Firing Boiler has reduced from 400 ppm to____ a. 100ppm b. 200ppm c. 300ppm d. 400ppm

Last Answer : Ans:- b. 200ppm

The main limitation for power handling capability of short length transmission lines and cables is

Description : The main limitation for power handling capability of short length transmission lines and cables is (A) power factor (B) stability (C) thermal effect limit (D) conductor size

Last Answer : The main limitation for power handling capability of short length transmission lines and cables is thermal effect limit

Cox chart, which is useful in the design of distillation column particularly for petroleum hydrocarbons, is a plot of (where, P = vapor pressure, T = temperature). (A) log P vs. T (B) log P vs. log T (C) T vs. P (D) P vs. log T

Description : Cox chart, which is useful in the design of distillation column particularly for petroleum hydrocarbons, is a plot of (where, P = vapor pressure, T = temperature). (A) log P vs. T (B) log P vs. log T (C) T vs. P (D) P vs. log T

Last Answer : (A) log P vs. T

The quantity of heat required to raise the temperature of a given substance by 1 oC is known as: a) sensible heat b) specific heat c) heat capacity d) latent heat

Description : The quantity of heat required to raise the temperature of a given substance by 1 oC is known as: a) sensible heat b) specific heat c) heat capacity d) latent heat

Last Answer : specific heat specific heat is the quantity of heat required to raise the temperature of 1 gram substance by 1 oC is

From which of the following is benefit of computer integrated manufacturing(CIM). a.Reduced lead time b.Increased production time c.Reduced productivity d.All of the above

Description : From which of the following is benefit of computer integrated manufacturing(CIM). a.Reduced lead time b.Increased production time c.Reduced productivity d.All of the above

Last Answer : a.Reduced lead time

Form which of the following is the objective of cellular manufacturing. a.Reduced manufacturing lead time b.Increased in quality c.Reduced setup time d.All of the above

Description : Form which of the following is the objective of cellular manufacturing. a.Reduced manufacturing lead time b.Increased in quality c.Reduced setup time d.All of the above

Last Answer : d.All of the above

impose limitation on design. (a) Saturation (b) Temperature rise (c) Efficiency (d) Power factor (e) All above

Description : impose limitation on design. (a) Saturation (b) Temperature rise (c) Efficiency (d) Power factor (e) All above

Last Answer : (e) All above

Ceramic remunerators can withstand temperatures up to: a) 600 oC b) 1300 oC c) 1700oC d) 950oC

Description : Ceramic remunerators can withstand temperatures up to: a) 600 oC b) 1300 oC c) 1700oC d) 950oC

Last Answer : 1300 oC

The water level in an open well was depressed by pumping 2.5 m and recuperated 2.87 m in 3 hours and 50 minutes. The yield of the well per minute is (A) 0.0033 (B) 0.0044 (C) 0.0055 (D) 0.0066

Description : The water level in an open well was depressed by pumping 2.5 m and recuperated 2.87 m in 3  hours and 50 minutes. The yield of the well per minute is  (A) 0.0033  (B) 0.0044  (C) 0.0055  (D) 0.0066 

Last Answer : (C) 0.0055 

Cox chart is useful in the design of (A) Distillation column (B) Evaporator (C) Dryer (D) Crystallise

Description : Cox chart is useful in the design of (A) Distillation column (B) Evaporator (C) Dryer (D) Crystallise

Last Answer : (A) Distillation column

Principle of Experimental design is given by (A) R A Fisher (B) Wilcox (C)Cox and Cochran (D) WG Cochran

Description : Principle of Experimental design is given by (A) R A Fisher (B) Wilcox (C)Cox and Cochran (D) WG Cochran

Last Answer : (A) R A Fisher

Secondary code of the Opitz system is for_________ a.Design attributes b.Manufacturing attributes c.Production operation type & sequence d.Maintenance flow

Description : Secondary code of the Opitz system is for_________ a.Design attributes b.Manufacturing attributes c.Production operation type & sequence d.Maintenance flow

Last Answer : c.Production operation type & sequence

Supplementary code of the Opitz system is for_________ a.Design attributes b.Manufacturing attributes c.Production operation type & sequence d.Maintenance flow

Description : Supplementary code of the Opitz system is for_________ a.Design attributes b.Manufacturing attributes c.Production operation type & sequence d.Maintenance flow

Last Answer : b.Manufacturing attributes

Form code of the Opitz system is for_________ a.Design attributes b.Manufacturing attributes c.Production operation type & sequence d.Maintenance flow

Description : Form code of the Opitz system is for_________ a.Design attributes b.Manufacturing attributes c.Production operation type & sequence d.Maintenance flow

Last Answer : a.Design attributes

____ is the bridge between design and manufacturing a.Production planning b.Process Planning c.Product design d.None of the above

Description : ____ is the bridge between design and manufacturing a.Production planning b.Process Planning c.Product design d.None of the above

Last Answer : b.Process Planning

CAD/CAM is the relationship between a.science and engineering b.manufacturing and marketing c.design and manufacturing d.design and marketing

Description : CAD/CAM is the relationship between a.science and engineering b.manufacturing and marketing c.design and manufacturing d.design and marketing

Last Answer : c.design and manufacturing

A system that automates the drafting process with interactive computer graphics iscalled a.Computer Aided Engineering (CAE) b.Computer Aided Design (CAD) c.Computer Aided Manufacturing (CAM) d.Computer Aided Instruction (CAI)

Description : A system that automates the drafting process with interactive computer graphics iscalled a.Computer Aided Engineering (CAE) b.Computer Aided Design (CAD) c.Computer Aided Manufacturing (CAM) d.Computer Aided Instruction (CAI)

Last Answer : b.Computer Aided Design (CAD)

n a chemical factory where dyes are made, wet cake at 30 OC consisting of 60% moisture is put in a dryer to obtain an output having only 5% moisture, at atmospheric pressure. In each batch about 120 kgs of material is dried. a. The quantity of moisture removed per batch. b. What is the total quantity ( sensible & latent) of heat required to evaporate the moisture, if the latent heat of water is 540 kcal/kg at atmospheric conditions, Ignore heat absorbed by the solids c. Find the quantity of steam required for the drying process (per batch), if steam at 4 kg/cm2 is used for generating hot air in the dryer and the dryer efficiency is 80%. Latent heat of steam at 4 kg/cm2 is 520 kcal/kg.

Description : n a chemical factory where dyes are made, wet cake at 30 OC consisting of 60% moisture  is put in a dryer to obtain an output having only 5% moisture, at atmospheric pressure. In  each batch about 120 ... dryer and the dryer efficiency  is 80%. Latent heat of steam at 4 kg/cm2 is 520 kcal/kg.

Last Answer : Given that   Qty of material dried per batch - 120 Kgs  Moisture at inlet - 60% a. The quantity of moisture removed per batch.  Water quantity in a wet batch - 120 x 0.6 = 72 Kgs.  Quantity of bone dry ... - 48/0.95 = 50.5 Kgs.  Equivalent water in a dry batch - 50.5 - 48 = 2.5 Kgs.

Pick out the wrong statement. (A) Biological oxygen demand (B.O.D.) value of a sewerage sample is always lower than its chemical oxygen demand (C.O.D.) value (B) Environmental pollution by NOx emission is much higher by four stroke petrol engines as compared to the two stroke engines (C) Temperature in stratosphere rises with increasing altitude (D) The characteristic of a green house body is that it allows the long wavelength incoming solar radiation to come in but does not allow the short wavelength infra red radiation to escape out of the earth's atmosphere

Description : Pick out the wrong statement. (A) Biological oxygen demand (B.O.D.) value of a sewerage sample is always lower than its chemical oxygen demand (C.O.D.) value (B) Environmental pollution by ... in but does not allow the short wavelength infra red radiation to escape out of the earth's atmosphere

Last Answer : (D) The characteristic of a green house body is that it allows the long wavelength incoming solar radiation to come in but does not allow the short wavelength infra red radiation to escape out of the earth's atmosphere

Maximum spindle speed limitation code in CNC Machine a.G90 b.G91 c.G92 d.G93

Description : Maximum spindle speed limitation code in CNC Machine a.G90 b.G91 c.G92 d.G93

Last Answer : c.G92

Tall women, have you experienced any difficulty dating, etc. because of your height?

Description : Tall women, have you experienced any difficulty dating, etc. because of your height?

Last Answer : I am a tall man and I would like to know where these tall women are at? I joined Match and I only found 2 women who are taller than 5’11” and they are not in any rush to reply to my emails.

What is the ideal temperature range for fish farming a. Less than 15 oC b. 20-30 oC c. 30-40 oC d. 15-20 Oc

Description : What is the ideal temperature range for fish farming a. Less than 15 oC b. 20-30 oC c. 30-40 oC d. 15-20 Oc

Last Answer : b. 20-30 oC

Energy audit will help to keep focus on _____ which occurs in energy. a) difficulty b) change c) variations d) conversion

Description : Energy audit will help to keep focus on _____ which occurs in energy. a) difficulty b) change c) variations d) conversion

Last Answer : variations

How much heat does it take to raise the temperature of 0.10 kg of aluminum by 25 oC?

Description : How much heat does it take to raise the temperature of 0.10 kg of aluminum by 25 oC?

Last Answer : Feel Free to Answer

The optimum temperature for the germination of soybean is: (a) 11 OC (b) 20 OC(c) 15 OC (d) 22 OC

Description : The optimum temperature for the germination of soybean is: (a) 11 OC (b) 20 OC(c) 15 OC (d) 22 OC

Last Answer : (d) 22 OC

Identify the correct statement for air compressors. a. For every 5.5oC drop in the inlet air temperature, the increase in energy consumption is by 2%. b. For every 4 oC rise in the inlet air temperature, the decrease in energy consumption is by 1% c. For every 4 oC rise in the inter air temperature, the increase in energy consumption is by 1% d. The energy consumption remains same irrespective of inlet air temperature

Description : Identify the correct statement for air compressors. a. For every 5.5oC drop in the inlet air temperature, the increase in energy consumption is by 2%. b. For every 4 oC rise in ... increase in energy consumption is by 1% d. The energy consumption remains same irrespective of inlet air temperature 

Last Answer : c. For every 4 oC rise in the inter air temperature, the increase in energy consumption is by 1% 

Answer: b Metabolic response to injury results in increased energy expenditure. If energy intake is less than expenditure, oxidation of body fat stores and erosion of lean body mass will occur with resultant loss of weight. When weight loss exceeds 10–15% of body weight, the complications of malnutrition interact with disease processes, with increased morbidity and mortality rates. The goal of nutritional support is maintenance of body cell mass and limitation of weight loss to less than 10% preinjury. The major impact of nutritional support in the trauma patient is to aid host defense. Under-nutrition may compromise the available host defense mechanism and may thus increase the likelihood of invasive sepsis, multiple organ system failure, and death. Resuscitation, oxygenation and arrest

Description : Answer: b Metabolic response to injury results in increased energy expenditure. If energy intake is less than expenditure, oxidation of body fat stores and erosion of lean body mass will occur ... requirements, caloric requirements should be distributed at a ratio of 70% as glucose and 30% as fat

Last Answer : Which of the following statement(s) is/are true concerning body fuel reserves? a. The largest fuel reserve in the body is skeletal muscle b. Fat provides about 9 calories/gram c. Free glucose and glycogen stores are a trivial fuel reserve d. Body protein is a valuable storage form of energy

What was the major operational limitation of early communications satellites?

Description : What was the major operational limitation of early communications satellites?

Last Answer : The lack of suitable power sources.

The major limitation in the use of clozapine for treatment of schizophrenia is: A. Its potential to cause agranulocytosis B. Its inability to benefit negative symptoms of schizophrenia C. High incidence of extrapyramidal side effects

Description : The major limitation in the use of clozapine for treatment of schizophrenia is: A. Its potential to cause agranulocytosis B. Its inability to benefit negative symptoms of schizophrenia C. High incidence of extrapyramidal side effects

Last Answer : A. Its potential to cause agranulocytosis

The major limitation of the thiazolidinediones in the treatment of type 2 diabetes mellitus is: A. Frequent hypoglycaemic episodes B. Hyperinsulinemia C. Lactic acidosis D. Low hypoglycaemic efficacy in moderate to severe cases

Description : The major limitation of the thiazolidinediones in the treatment of type 2 diabetes mellitus is: A. Frequent hypoglycaemic episodes B. Hyperinsulinemia C. Lactic acidosis D. Low hypoglycaemic efficacy in moderate to severe cases

Last Answer : D. Low hypoglycaemic efficacy in moderate to severe cases

Pick out the correct statement. (A) Noise from ball mills can be dealt with by fibre glass lined enclosures (B) Noise from vibrating chutes can be reduced by lining the metallic chute with rubber (C) Noise of conveyor belt system is reduced by using urethane coated cloth conveyor belts and rubber/plastic covered metallic rollers (D) All (A), (B) & (C)

Description : Pick out the correct statement. (A) Noise from ball mills can be dealt with by fibre glass lined enclosures (B) Noise from vibrating chutes can be reduced by lining the metallic chute with rubber (C) Noise ... cloth conveyor belts and rubber/plastic covered metallic rollers (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Two samples of lead oxide were separately reduced to metallic lead by heating in a current of hydrogen. The weight of lead from one oxide was half the weight of lead obtained from the other oxide. The data illustrates [AMU 1983] (A) Law of reciprocal proportions (B) Law of constant proportions (C) Law of multiple proportions (D) Law of equivalent proportions

Description : Two samples of lead oxide were separately reduced to metallic lead by heating in a current of hydrogen. The weight of lead from one oxide was half the weight of lead obtained from the other oxide. ... (B) Law of constant proportions (C) Law of multiple proportions (D) Law of equivalent proportions

Last Answer : (C) Law of multiple proportions

Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Description : Power required for a train weighing 200 Mg to move at a uniform speed of 60 Kmph up an incline of 1 in 200 is (Resistance due to friction is negligible) a.16.67 KW b.163.5 KW c.1000 KW d.9810 KW e.Tapered bearing

Last Answer : b. 163.5 KW

. One of the major difficulties in the biological control of insect pest is that (a) the method is less effective as compared with the use of insecticides (b) the practical difficulty of introducing the predator to specific areas (c) the predator develops a preference to other diets and may itself become a pest (d) the predator does not always survive when transferred to a new environment.

Description : . One of the major difficulties in the biological control of insect pest is that (a) the method is less effective as compared with the use of insecticides (b) the practical difficulty of introducing ... become a pest (d) the predator does not always survive when transferred to a new environment.

Last Answer : (d) the predator does not always survive when transferred to a new environment.

A major problem with using style modification is that 1. customers have difficulty recognizing that a change has been made 2. such changes do not yield long lasting appeal 3. customers may perceive such modifications as less attractive 4. they are almost always very costly 5. none of these

Description : A major problem with using style modification is that 1. customers have difficulty recognizing that a change has been made 2. such changes do not yield long lasting appeal 3. customers may perceive such modifications as less attractive 4. they are almost always very costly 5. none of these

Last Answer : customers may perceive such modifications as less attractive

A major problem with using style modification is that: A)customers have difficulty recognising that a change has been made B)such changes do not yield long -lasting appeal C)customers may perceive such modifications as less attractive D)they are almost always very costly

Description : A major problem with using style modification is that: A)customers have difficulty recognising that a change has been made B)such changes do not yield long-lasting appeal C)customers may perceive such modifications as less attractive D)they are almost always very costly

Last Answer : C)customers may perceive such modifications as less attractive

The major shortcoming of waterfall model is (A) the difficulty in accommodating changes after requirement analysis. (B) the difficult in accommodating changes after feasibility analysis. (C) the system testing. (D) the maintenance of system.

Description : The major shortcoming of waterfall model is (A) the difficulty in accommodating changes after requirement analysis. (B) the difficult in accommodating changes after feasibility analysis. (C) the system testing. (D) the maintenance of system.

Last Answer : (A) the difficulty in accommodating changes after requirement analysis.

Accidental poisonings are common with both aspirin and ibuprofen, two OC drugs available in tasty chewable tablets. In cases of overdose, aspirin is more likely than ibuprofen to cause (a) Autonomic Instability (b) Hepatic necrosis (c) Metabolic acidosis (d) Thrombocytopenia (e) Ventricular arrhythmias

Description : Accidental poisonings are common with both aspirin and ibuprofen, two OC drugs available in tasty chewable tablets. In cases of overdose, aspirin is more likely than ibuprofen to cause (a) ... Instability (b) Hepatic necrosis (c) Metabolic acidosis (d) Thrombocytopenia (e) Ventricular arrhythmias

Last Answer : Ans: C