Heat recovery provides valuable energy sources and ....... consumption. a) Reduce energy b) Increase energy c) Increase fuel d) Reduce fuel

Heat recovery provides valuable energy sources and ....... consumption.
a) Reduce energy
b) Increase energy
c) Increase fuel
d) Reduce fuel
by

1 Answer

Answer :

Reduce energy
by

Related questions

A waste heat recovery system in industrial process has been key to reduce ....... Consumption. a) Coal b) Fuel c) Biogas d) Oil

Description : A waste heat recovery system in industrial process has been key to reduce ....... Consumption. a) Coal b) Fuel c) Biogas d) Oil

Last Answer : Fuel

What are the benefits or the advantages of waste heat recovery units (WHRU)? a) Reduced Pollution b) Reduced equipment sizes c) Reduced auxiliary energy consumption. d) All of the above

Description : What are the benefits or the advantages of waste heat recovery units (WHRU)? a) Reduced Pollution b) Reduced equipment sizes c) Reduced auxiliary energy consumption. d) All of the above

Last Answer : All of the above

The primary objective of energy audit is to determine ways to ______ energy consumption per unit of product output. A. Increase. C) Slightly increase. B. Reduce. D) Change.

Description : The primary objective of energy audit is to determine ways to ______ energy consumption per unit of product output. A. Increase. C) Slightly increase. B. Reduce. D) Change.

Last Answer : reduce

How promising is the "air lubrication" idea to increase the speed of ships and reduce the consumption of fuel?

Description : How promising is the "air lubrication" idea to increase the speed of ships and reduce the consumption of fuel?

Last Answer : I think passive systems, like shark skin like surfaces, will be more promising than active systems, as those also consume energy. I am also not sure how the bubbles would affect the vessels buoyancy.

Benefits of Waste Heat Recovery a. Reduction in pollution b. Reduction in equipment sizes c. Reduction in auxiliary energy consumption d. All of the above

Description : Benefits of Waste Heat Recovery a. Reduction in pollution b. Reduction in equipment sizes c. Reduction in auxiliary energy consumption d. All of the above

Last Answer : Ans:- d. All of the above

BEE star rating is solely based on appliance's power .................. A) Consumption. C) Delivery. B) Recovery. D) Rejection.

Description : BEE star rating is solely based on appliance's power .................. A) Consumption. C) Delivery. B) Recovery. D) Rejection.

Last Answer : Consumption.

A major advantage of waste heat recovery in industry is a) Reduction in pollution c) Increase efficiency d) None of the above

Description : A major advantage of waste heat recovery in industry is a) Reduction in pollution c) Increase efficiency d) None of the above

Last Answer : Reduction in pollution

Major advantage of waste heat recovery in industry is: a) Reduction in pollution b) increase in efficiency c) Both a & b d) none of the above

Description : Major advantage of waste heat recovery in industry is: a) Reduction in pollution b) increase in efficiency c) Both a & b d) none of the above

Last Answer : Both a & b

108. is primarily a management technique that uses energy information as a basis to eliminate waste, reduce and control current level of energy use and improve the existing operating procedures. a) Energy monitoring and targeting b) CUSUM c) Specific energy consumption d) Production

Description : 108.is primarily a management technique that uses energy information as a basis to eliminate waste, reduce and control current level of energy use and improve the existing operating procedures. a) Energy monitoring and targeting b) CUSUM c) Specific energy consumption d) Production

Last Answer : Energy monitoring and targeting

________ to reduce or control energy consumption. a] Determining c] Highlighting b] Recording d] Setting Targets

Description : ________ to reduce or control energy consumption. a] Determining c] Highlighting b] Recording d] Setting Targets

Last Answer : setting targets

According to……………… ―energy audit‖ means verification, monitoring, analysis of use of energy including submission of technical report containing recommendations for improving energy efficiency with cost benefit analysis and an action plan to reduce energy consumption a) Energy conservation act 2001 b) Industrial act 1946 c) Factory act 1947 d) none of act

Description : According to -energy audit means verification, monitoring, analysis of use of energy including submission of technical report containing recommendations for improving energy efficiency with cost benefit analysis ... act 2001 b) Industrial act 1946 c) Factory act 1947 d) none of act

Last Answer : Energy conservation act 2001

Total primary energy consumption of fuel in the world is lead by a) Coal b) Nuclear c) Hydro d) Oil

Description : Total primary energy consumption of fuel in the world is lead by a) Coal b) Nuclear c) Hydro d) Oil

Last Answer : coal

105. Energy and production data is useful to calculate…… a) Specific Energy Consumption b) Specific Fuel consumption c) Specific Cost d) None

Description : 105. Energy and production data is useful to calculate…… a) Specific Energy Consumption b) Specific Fuel consumption c) Specific Cost d) None

Last Answer : Specific Energy Consumption

71. Total primary energy consumption of fuel in the world is lead by a) Coal b) Nuclear c) Hydro d) Oil

Description : 71. Total primary energy consumption of fuel in the world is lead by a) Coal b) Nuclear c) Hydro d) Oil

Last Answer : coal

Energy and production data is useful to calculate…… a) Specific Energy Consumption b) Specific Fuel consumption c) Specific Cost d) None

Description : Energy and production data is useful to calculate…… a) Specific Energy Consumption b) Specific Fuel consumption c) Specific Cost d) None

Last Answer : Specific Energy Consumption

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30(C) 7 (D) 70

Description : Major sources of noise in furnace operation arises from air inspirators, combustion, side wall vibrations and fluctuation in the process heat load. A 50% increase in fuel firing rate may increase the furnace noise level by about __________ decibels. (A) 3 (B) 30 (C) 7 (D) 70

Last Answer : (A) 3

A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Description : A waste heat recovery unit (WHRU) is an_________ that transfers heat from process outputs at high temperature to another part of the process for some purpose, usually increased efficiency. a) Energy recovery heat exchanger b) Energy recovery heat diffuser c) Both ‘a’ and ‘b’ d) None of the above

Last Answer : Energy recovery heat exchanger

A waste heat recovery unit is an energy recovery heat exchanger that transfers heat from process outputs at ........ a) High temperature b) Medium temperature c) Low temperature d) Both a & b

Description : A waste heat recovery unit is an energy recovery heat exchanger that transfers heat from process outputs at ........ a) High temperature b) Medium temperature c) Low temperature d) Both a & b

Last Answer : High temperature

One of the key areas for ....... energy saving in existing systems is waste heat recovery. a) Potential b) Kinetic c) Thermal d) Electrical

Description : One of the key areas for ....... energy saving in existing systems is waste heat recovery. a) Potential b) Kinetic c) Thermal d) Electrical

Last Answer : Potential

Energy recovery is typically via production of ____ a) Gas b) Heat c) Light d) Steam

Description : Energy recovery is typically via production of ____ a) Gas b) Heat c) Light d) Steam

Last Answer : Steam

Can GPS trackers reduce fuel consumption?

Description : Can GPS trackers reduce fuel consumption?

Last Answer : A GPS tracker has very little o do with fuel consumption. Using a GPS will, however, allow you to plan the shortest route to your destination thereby reducing the fuel consumption.

Which of the following processes is not an example of adsorption applied to gaseous separations? (A) Recovery of valuable solvent vapors from dilute mixture with air and other gases (B) Dehumidification of air and gas (C) Removal of objectionable odour and impurities from industrial gases (D) Decolouration of yellow glycerine

Description : Which of the following processes is not an example of adsorption applied to gaseous separations? (A) Recovery of valuable solvent vapors from dilute mixture with air and ... Removal of objectionable odour and impurities from industrial gases (D) Decolouration of yellow glycerine

Last Answer : (D) Decolouration of yellow glycerine

Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent. (A) 1 (B) 10 (C) 30 (D) 50

Description : Use of economiser in a boiler plant reduces the fuel consumption for steam generation by about __________ percent. (A) 1 (B) 10 (C) 30 (D) 50

Last Answer : (B) 10

Choke in a I.C. engine is used to control a) Camshaft speed b) Specific fuel consumption c) Air fuel mixture d) Crankshaft speed Ans. c

Description : Choke in a I.C. engine is used to control a) Camshaft speed b) Specific fuel consumption c) Air fuel mixture d) Crankshaft speed Ans. c

Last Answer : ans c

Tractors with less specific fuel consumption should be preferred because..... A. High efficiency C. Good output B. Good for field D. Less cost.

Description : Tractors with less specific fuel consumption should be preferred because..... A. High efficiency C. Good output B. Good for field D. Less cost

Last Answer : Less cost

The ratio of the total amount of heat that equipment can remove from the indoors to travel and amount of energy consumed by the equipment is known as A) Energy performance ratio (EPR). C) Energy efficiency RATIO (EER). B) Energy consumption ratio (ECR). D) None of the above

Description : . The ratio of the total amount of heat that equipment can remove from the indoors to travel and amount of energy consumed by the equipment is known as A) Energy performance ratio (EPR). C) Energy efficiency RATIO (EER). B) Energy consumption ratio (ECR). D) None of the above

Last Answer : Energy efficiency RATIO (EER).

The use of pressurized radiator cap is to a) Reduce evaporation loss b) Increase engine operating temperature c) Increase boiling point of water d) Reduce heat losses

Description : The use of pressurized radiator cap is to a) Reduce evaporation loss b) Increase engine operating temperature c) Increase boiling point of water d) Reduce heat losses

Last Answer : ans c

To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Description : To reduce the stack loss, heat recovery from flue gas can be done by (A) Preheating of cold stock (B) Preheating of combustion air (C) Steam generation in waste heat boilers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Description : Pitch creosote mixture (PCM) as compared to furnace oil is a better fuel, because its (A) Emissivity factor is higher (B) Sulphur content is lower (C) Flue gas has lower dew point thereby facilitating more waste heat recovery (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

First law of thermodynamics  (a) enables to determine change in internal energy of the system  (b) does not help to predict whether the system will or not undergo a change  (c) does not enable to determine change in entropy  (d) provides relationship between heat, work and internal energy  (e) all of the above.

Description : First law of thermodynamics  (a) enables to determine change in internal energy of the system  (b) does not help to predict whether the system will or not undergo a change  (c) does not enable ... entropy  (d) provides relationship between heat, work and internal energy  (e) all of the above.

Last Answer : Answer : e

In industrial operations fluids with temperature less than __________ are set as the limit for waste heat recovery because of the risk of condensation of corrosive liquids a. 80C b. 100C c. 120C d. 200C

Description : In industrial operations fluids with temperature less than __________ are set as the limit for waste heat recovery because of the risk of condensation of corrosive liquids a. 80C b. 100C c. 120C d. 200C

Last Answer : 100C

Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat of the substance): 0.20 kCal/kg oC DT (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Description : Calculate the recoverable waste heat (Q, in kCal/hour) from flue gases using the followingparameters: V (flow rate of the substance) 2000 m3/hr r (density of the flue gas): 0.9 kg/m3 Cp (specific heat ... (temperature difference): 120 oC h (recovery factor): 50% a. 21600 b. 43200 c. 25600 d. 34000

Last Answer : 21600

A high temperature waste heat recovery unit consists of recovering waste heat at temperaturesgreater than _______. a) 200 °C b) 500 °C c) 300 °C d) 400 °C

Description : A high temperature waste heat recovery unit consists of recovering waste heat at temperaturesgreater than _______. a) 200 °C b) 500 °C c) 300 °C d) 400 °C

Last Answer : 400 °C

The waste heat recovery unit (WHRU) is a tool involved in _______. a) Regeneration b) Cogeneration c) Both ‘a’ and ‘b’ d) None of the above

Description : The waste heat recovery unit (WHRU) is a tool involved in _______. a) Regeneration b) Cogeneration c) Both ‘a’ and ‘b’ d) None of the above

Last Answer : Cogeneration

Techniques of waste heat recovery ....... a) Direct contact condensation b) Indirect contact condensation c) Transport membrane condensation d) All of the above

Description : Techniques of waste heat recovery ....... a) Direct contact condensation b) Indirect contact condensation c) Transport membrane condensation d) All of the above

Last Answer : All of the above

Nellore to medium temperature waste heat recovery system the most suitable device is ------ a) Economizer b) Heat wheels c) Air preheater d) Recuperate d) Carbonate

Description : Nellore to medium temperature waste heat recovery system the most suitable device is ------ a) Economizer b) Heat wheels c) Air preheater d) Recuperate d) Carbonate

Last Answer : Heat wheels

Recovery of waste heat from hot fluid to fluid is called: a) thermo compressor b) waste heat recovery boiler c) heat Pump d) economizer

Description : Recovery of waste heat from hot fluid to fluid is called: a) thermo compressor b) waste heat recovery boiler c) heat Pump d) economizer

Last Answer : heat Pump

Recovery of heat from dryer exhaust air is a typical application of: a) Waste heat recovery boiler b) Heat pump c) Heat wheel d) Economizer

Description : Recovery of heat from dryer exhaust air is a typical application of: a) Waste heat recovery boiler b) Heat pump c) Heat wheel d) Economizer

Last Answer : Heat wheel

In a low to medium temperature waste heat recovery system which of the device is most suitable a) Economiser b) Heat wheels c) air preheater d) Recuperator

Description : In a low to medium temperature waste heat recovery system which of the device is most suitable a) Economiser b) Heat wheels c) air preheater d) Recuperator

Last Answer : Heat wheels

Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Description : Air preheater is not used as a waste heat recovery system in a____. a) Boiler b) billet Reheating Furnace c) Heat treatment furnace d) compressor

Last Answer : compressor

Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Description : Recuperated is used mainly as a waste heat recovery system in a ____. a) Boiler b) Billet Reheating Furnace c) Compressor d) None of the above

Last Answer : Billet Reheating Furnace

Heat recovery equipment will be most effective when the temperature of flue gas is: a) 250oC b) 200 oC c)400 oC d) 280 oC

Description : Heat recovery equipment will be most effective when the temperature of flue gas is: a) 250oC b) 200 oC c)400 oC d) 280 oC

Last Answer : 400 oC

Which of the following used to improve Online Reputation? A. Improve tagging and SEO B. Strive to build links from strong and reliable sources C. Publish original posts with valuable information D. All of the above

Description : Which of the following used to improve Online Reputation? A. Improve tagging and SEO B. Strive to build links from strong and reliable sources C. Publish original posts with valuable information D. All of the above

Last Answer : D. All of the above

Heat balance of furnace provides means of determining the (A) Thermal efficiency of the process (B) Sources of heat losses (C) Scope of reduction of heat losses(D) All (A), (B) and (C)

Description : Heat balance of furnace provides means of determining the (A) Thermal efficiency of the process (B) Sources of heat losses (C) Scope of reduction of heat losses (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Limestone is added in the blast furnace (during pig iron manufacture) to (A) Form slag by combining with impurities (B) Supply heat by undergoing exothermic reaction with impurities (C) Reduce the coke consumption (D) Reduce slag viscosity

Description : Limestone is added in the blast furnace (during pig iron manufacture) to (A) Form slag by combining with impurities (B) Supply heat by undergoing exothermic reaction with impurities (C) Reduce the coke consumption (D) Reduce slag viscosity

Last Answer : Option A

Infrared spectroscopy provides valuable information about A. Molecular weight B. Melting point C. Conjugation D. Functional groups

Description : Infrared spectroscopy provides valuable information about A. Molecular weight B. Melting point C. Conjugation D. Functional groups

Last Answer : Functional groups

The ultimate aim to encourage the enterprise to save the energy , reduce the production cost and increase economic benefits is ____ A. Energy audit C. Energy saving B. Energy management D. Energy

Description : The ultimate aim to encourage the enterprise to save the energy , reduce the production cost and increase economic benefits is ____ A. Energy audit C. Energy saving B. Energy management D. Energy

Last Answer : Energy management

The ultimate aim of energy audit is to encourage enterprises to…… a) Save energy b) Reduce production cost c) Increase economic benefit d) All of the above

Description : The ultimate aim of energy audit is to encourage enterprises to…… a) Save energy b) Reduce production cost c) Increase economic benefit d) All of the above

Last Answer : All of the above

. How can we increase the efficiency of a cooling tower? a. Save energy. b. Reduce the amount of water being consumed. c. Decrease the amount of chemicals required for water treatment. d. All of above

Description : . How can we increase the efficiency of a cooling tower? a. Save energy. b. Reduce the amount of water being consumed. c. Decrease the amount of chemicals required for water treatment. d. All of above

Last Answer : All of above