Solvent used in Edeleanu process is (A) Furfural (B) Propane (C) Liquid SO2 (D) Phenol

Solvent used in Edeleanu process is
(A) Furfural
(B) Propane
(C) Liquid SO2
(D) Phenol
by

1 Answer

Answer :

(C) Liquid SO2
by

Related questions

Solvent used in duo-sol extraction for lube oil upgradation is a mixture of (A) Propane & phenol-cresol mixture(B) Methyl ethyl ketone & glycol(C) Phenol & furfural(D) Propane & liquid sulphur dioxide

Description : Solvent used in duo-sol extraction for lube oil upgradation is a mixture of (A) Propane & phenol-cresol mixture (B) Methyl ethyl ketone & glycol (C) Phenol & furfural (D) Propane & liquid sulphur dioxide

Last Answer : (A) Propane & phenol-cresol mixture

Solvent used in the deasphalting process is (A) Furfural (B) Phenol (C) Propane (D) Hexane

Description : Solvent used in the deasphalting process is (A) Furfural (B) Phenol (C) Propane (D) Hexane

Last Answer : (C) Propane

Which of the following is used as a solvent in deasphalting of petroleum products? (A) Furfural (B) Propane (C) Methyl ethyl ketone (D) Liquid sulphur dioxide

Description : Which of the following is used as a solvent in deasphalting of petroleum products? (A) Furfural (B) Propane (C) Methyl ethyl ketone (D) Liquid sulphur dioxide

Last Answer : (B) Propane

Raw Kerosene has a smoke point of 15 mm. After it is subjected to dearomatization by liquid SO2 extraction (Edeleanu process), its smoke point may become __________ mm. (A) 5 (B) 10 (C) 25 (D) 100

Description : Raw Kerosene has a smoke point of 15 mm. After it is subjected to dearomatization by liquid SO2 extraction (Edeleanu process), its smoke point may become __________ mm. (A) 5 (B) 10 (C) 25 (D) 100

Last Answer : (C) 25

Solvent used for dewaxing of petroleum products are (A) Furfural (B) Methyl ethyl ketone (MEK) (C) Propane (D) Both (B) & (C

Description : Solvent used for dewaxing of petroleum products are (A) Furfural (B) Methyl ethyl ketone (MEK) (C) Propane (D) Both (B) & (C

Last Answer : (C) Propane

The solvent used in Barisol dewaxing process is (A) Hexane (B) Furfural (C) Benzol and ethylene dichloride (D) Methyl ethyl ketone (MEK

Description : The solvent used in Barisol dewaxing process is (A) Hexane (B) Furfural (C) Benzol and ethylene dichloride (D) Methyl ethyl ketone (MEK

Last Answer : (C) Benzol and ethylene dichloride

Furfural solvent extraction is used for upgrading (by dissolving aromatics) (A) Naphtha (B) Lubricating oils (C) Wax (D) Cracking feedstock

Description : Furfural solvent extraction is used for upgrading (by dissolving aromatics) (A) Naphtha (B) Lubricating oils (C) Wax (D) Cracking feedstock

Last Answer : (B) Lubricating oils

Solvent used for extraction of oil is (A) Hexane (B) Methyl ethyl ketone (C) Furfural (D) None of these

Description : Solvent used for extraction of oil is (A) Hexane (B) Methyl ethyl ketone (C) Furfural (D) None of these

Last Answer : (A) Hexane

Extractor temperature is maintained at -20°C in Edeleanu process to reduce the __________ of kerosene. (A) Smoke point (B) Paraffins (C) Aromatics (D) Naphthenes

Description : Extractor temperature is maintained at -20°C in Edeleanu process to reduce the __________ of kerosene. (A) Smoke point (B) Paraffins (C) Aromatics (D) Naphthenes

Last Answer : (B) Paraffins

Solvent used in the Udex (glycol) extraction process for removal of light aromatics from cracked naphtha is (A) Propane (B) Diethylene glycol (C) Aqueous solution (10% water) of diethylene glycol (D) Methyl ethyl ketone (MEK)

Description : Solvent used in the Udex (glycol) extraction process for removal of light aromatics from cracked naphtha is (A) Propane (B) Diethylene glycol (C) Aqueous solution (10% water) of diethylene glycol (D) Methyl ethyl ketone (MEK)

Last Answer : (C) Aqueous solution (10% water) of diethylene glycol

Which of the following is the most commonly used leaching solvent in vegetable oil industry? (A) Phenol (B) Hexane

Description : Which of the following is the most commonly used leaching solvent in vegetable oil industry? (A) Phenol (B) Hexane

Last Answer : (B) Hexane

The most suitable solvent for deasphalting vacuum residue is (A) Propane (B) Methyl ethyl ketone (C) Doctor's solution (D) Methanol amine

Description : The most suitable solvent for deasphalting vacuum residue is (A) Propane (B) Methyl ethyl ketone (C) Doctor's solution (D) Methanol amine

Last Answer : (B) Methyl ethyl ketone

Which one of the following can be oxidized to the corresponding carbonyl compound - (1) O-Nitrophenol (2) Phenol (3) 2-methyl-2-hydroxy propane (4) 2-hydroxy propane

Description : Which one of the following can be oxidized to the corresponding carbonyl compound - (1) O-Nitrophenol (2) Phenol (3) 2-methyl-2-hydroxy propane (4) 2-hydroxy propane

Last Answer : (4) 2-hydroxy propane

Saccharin is made up of – (1) Toluene (2) Phenol (3) Propane (4) Butane

Description : Saccharin is made up of – (1) Toluene (2) Phenol (3) Propane (4) Butane

Last Answer : (1) Toluene Explanation: Saccharin can be produced in various ways. The original route by Remsen & Fahlberg starts with toluene. Saccharin ism artificial sweetener. The basic substance, benzoic sulfiloine ... It is used to sweeten products such as drinks, candies, cookies, medicines, and toothpaste.

Saccharin is made up of (1) Toluene (2) Phenol (3) Propane (4) Butane

Description : Saccharin is made up of (1) Toluene (2) Phenol (3) Propane (4) Butane

Last Answer : Toluene

__________ is used as an 'entrainer' for the separation of acetic acid￾water mixture by distillation. (A) Furfural (B) Benzol (C) Butyl acetate (D) Hexane

Description : __________ is used as an 'entrainer' for the separation of acetic acid￾water mixture by distillation. (A) Furfural (B) Benzol (C) Butyl acetate (D) Hexane

Last Answer : (C) Butyl acetate

The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient(B) Increasing the liquid film co-efficient(C) Increasing the total pressure(D) Decreasing the total pressure

Description : The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient (B) Increasing the liquid film co-efficient (C) Increasing the total pressure (D) Decreasing the total pressure

Last Answer : (A) Increasing the gas film co-efficient

Treatment of pentoses with a concentrated mineral acid yields a cyclic aldehyde known as (A) Pentaldehyde (B) Cyclopental (C) Hexaldehyde (D) Furfural

Description : Treatment of pentoses with a concentrated mineral acid yields a cyclic aldehyde known as (A) Pentaldehyde (B) Cyclopental (C) Hexaldehyde (D) Furfural

Last Answer : Answer : D

The purple ring of Molisch reaction is due to (A) Furfural (B) Furfural + α Napthol (C) °C Napthol (D) Furfurol + H2SO4 + α -Naphthol

Description : The purple ring of Molisch reaction is due to (A) Furfural (B) Furfural + α Napthol (C) °C Napthol (D) Furfurol + H2SO4 + α -Naphthol

Last Answer : B

Formalin is an aqueous solution of (a) formaldehyde (b) flourescein (c) formic acid (d) furfural

Description : Formalin is an aqueous solution of (a) formaldehyde (b) flourescein (c) formic acid (d) furfural

Last Answer : Ans:(a)

Casing head gasoline is the liquid(A) Butane(B) Propane(C) Natural gas(D) Gasoline separated from wet natural gas by compression

Description : Casing head gasoline is the liquid (A) Butane (B) Propane (C) Natural gas (D) Gasoline separated from wet natural gas by compression

Last Answer : (A) Butane

If G = insoluble gas in gas stream and L = non-volatile solvent in liquid stream, then the slope of the operating line for the absorber is (A) L/G (B) G/L (C) Always < 1 (D) None of these

Description : If G = insoluble gas in gas stream and L = non-volatile solvent in liquid stream, then the slope of the operating line for the absorber is (A) L/G (B) G/L (C) Always < 1 (D) None of these

Last Answer : (A) L/G

The rate of solid-liquid extraction is limited by the (A) Phase change of the solute as it dissolves in the solvent (B) Diffusion of the solute through the solvent in the pores to the outside of the particle (C) Diffusion of the solute from the solution in contact with the particle to the main bulk of the solution (D) All 'a', 'b' & 'c'

Description : The rate of solid-liquid extraction is limited by the (A) Phase change of the solute as it dissolves in the solvent (B) Diffusion of the solute through the solvent in the pores to the outside of the particle (C) ... contact with the particle to the main bulk of the solution (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Solvent extraction is the terminology applied to the liquid-liquid extraction, which is preferred for the separation of the components of liquids, when (A) Extracting solvent is cheaply & abundantly available (B) One of the liquid components is heat sensitive (C) Viscosity of liquid components is very high (D) One of the liquid components has very high affinity towards the solvent

Description : Solvent extraction is the terminology applied to the liquid-liquid extraction, which is preferred for the separation of the components of liquids, when (A) Extracting solvent is cheaply & abundantly available ... very high (D) One of the liquid components has very high affinity towards the solvent

Last Answer : (D) One of the liquid components has very high affinity towards the solvent

Pick out the correct statement. (A) In case of liquid-liquid extraction, no separation is possible, if the selectivity of the solvent used is unity (B) With increase in temperature, the selectivity of the solvent used in solvent extraction decreases (C) The selectivity of solvent used in solvent extraction is unity at the plait point (D) All (A), (B) and (C)

Description : Pick out the correct statement. (A) In case of liquid-liquid extraction, no separation is possible, if the selectivity of the solvent used is unity (B) With increase in temperature, the selectivity of the solvent used ... in solvent extraction is unity at the plait point (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Separation of a mixture of two gases by absorption in the liquid solvent depends upon the difference in their (A) Viscosity (B) Density (C) Solubility (D) Relative volatility

Description : Separation of a mixture of two gases by absorption in the liquid solvent depends upon the difference in their (A) Viscosity (B) Density (C) Solubility (D) Relative volatility

Last Answer : (C) Solubility

The solvent used in liquid-liquid extraction should have __________ less than one. (A) Selectivity (B) Distribution co-efficient(C) Both (A) and (B)(D) Neither (A) nor (B)

Description : The solvent used in liquid-liquid extraction should have __________ less than one. (A) Selectivity (B) Distribution co-efficient (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

The solvent used in liquid extraction should not have high latent heat of vaporisation, because (A) The pressure drop and hence the pumping cost will be very high (B) It cannot be recovered by distillation (C) Its recovery cost by distillation may be prohibitively high (D) It will decompose while recovering by distillation

Description : The solvent used in liquid extraction should not have high latent heat of vaporisation, because (A) The pressure drop and hence the pumping cost will be very high (B) It cannot ... by distillation may be prohibitively high (D) It will decompose while recovering by distillation

Last Answer : (C) Its recovery cost by distillation may be prohibitively high

In liquid extraction, if the selectivity is unity, then (A) Separation of the constituents is the most effective (B) No separation will occur (C) Amount of solvent required will be minimum (D) Solvent flow rate should be very low

Description : In liquid extraction, if the selectivity is unity, then (A) Separation of the constituents is the most effective (B) No separation will occur (C) Amount of solvent required will be minimum (D) Solvent flow rate should be very low

Last Answer : (B) No separation will occur

The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of the following resistance (s) is (are) controlling? (A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Description : The individual mass transfer co-efficients (moles/m2s) for absorption of a solute from a gas mixture into a liquid solvent are, KL = 4.5 and KG = 1.5. The slope of the equilibrium line is 3. Which of ... A) Liquid side (B) Gas side (C) Interfacial (D) Both liquid and gas side

Last Answer : (B) Gas side

The worst enemy of ozone is a) Liquid NH3 b) SO2 c) CH4 d) CO.

Description : The worst enemy of ozone is a) Liquid NH3 b) SO2 c) CH4 d) CO.

Last Answer : c) CH4

Separation of __________ employs gaseous diffusion process. (A) N2 and O2 from air (B) Isotopes of uranium (C) Isotopes of helium (D) SO2 and air

Description : Separation of __________ employs gaseous diffusion process. (A) N2 and O2 from air (B) Isotopes of uranium (C) Isotopes of helium (D) SO2 and air

Last Answer : (B) Isotopes of uranium

In the converter of the contact process for the manufacture of H2SO4 the equilibrium conversion of SO2__________ (i) __________ with increase in temperature and __________ (ii) __________ with increase in the mole ratio of SO2 to air. (A) (i) increases (ii) decreases (B) (i) decreases (ii) increases (C) (i) increases (ii) increases (D) (i) decreases (ii) decreases

Description : In the converter of the contact process for the manufacture of H2SO4 the equilibrium conversion of SO2__________ (i) __________ with increase in temperature and __________ (ii) __________ with increase in the mole ratio ... increases (C) (i) increases (ii) increases (D) (i) decreases (ii) decreases

Last Answer : (B) (i) decreases (ii) increases

Sulphuric acid is used as a catalyst in the (A) Hydrogenation of oils (B) Gas phase oxidation of SO2 in chamber process (C) Alkylation of hydrocarbons(D) None of these

Description : Sulphuric acid is used as a catalyst in the (A) Hydrogenation of oils (B) Gas phase oxidation of SO2 in chamber process (C) Alkylation of hydrocarbons (D) None of these

Last Answer : (C) Alkylation of hydrocarbons

The catalytic converter for conversion of SO2 to SO3 by contact process should have a feed with SO2 content between (A) 2-5 % (B) 7-10 % (C) 12-15 % (D) 20-25 %

Description : The catalytic converter for conversion of SO2 to SO3 by contact process should have a feed with SO2 content between (A) 2-5 % (B) 7-10 % (C) 12-15 % (D) 20-25 %

Last Answer : (B) 7-10 %

In chamber process of sulphuric acid manufacture in industry, the gas phase oxidation of SO2 to SO3 is accomplished by a __________ reaction. (A) Non-catalytic homogeneous (B) Non-catalytic heterogeneous (C) Catalytic homogenous (D) Catalytic heterogeneous

Description : In chamber process of sulphuric acid manufacture in industry, the gas phase oxidation of SO2 to SO3 is accomplished by a __________ reaction. (A) Non-catalytic homogeneous (B) Non-catalytic heterogeneous (C) Catalytic homogenous (D) Catalytic heterogeneous

Last Answer : (C) Catalytic homogenous

Cooking liquor in case of sulphite process is (A) Sodium sulphite and sodium bisulphite (B) Magnesium sulphite and free SO2 in acid medium (C) Magnesium sulphate and magnesium bicarbonate (D) None of these

Description : Cooking liquor in case of sulphite process is (A) Sodium sulphite and sodium bisulphite (B) Magnesium sulphite and free SO2 in acid medium (C) Magnesium sulphate and magnesium bicarbonate (D) None of these

Last Answer : (A) Sodium sulphite and sodium bisulphite

How does Liquid Propane turn into gas?

Description : How does Liquid Propane turn into gas?

Last Answer : Liquid propane turns to gas by a process known as vaporization, in which liquid propane is boiled to turn liquid into gas vapor.

Is the liquid propane in a barbecue evaporates away because the user left the valve open a chemical or physical change?

Description : Is the liquid propane in a barbecue evaporates away because the user left the valve open a chemical or physical change?

Last Answer : It's a physical change. Chemically, it's still propane - butit's physically changed from a liquid to a gas.

Which of the following is the best description of propane, CH3CH2CH3, at room temperature? (a) liquid, soluble in H2O (b) gas, soluble in gasoline (c) liquid, soluble in gasoline (d) gas, soluble in water

Description : Which of the following is the best description of propane, CH3CH2CH3, at room temperature? (a) liquid, soluble in H2O (b) gas, soluble in gasoline (c) liquid, soluble in gasoline (d) gas, soluble in water

Last Answer : gas, soluble in gasoline

Through which molecules of both solvent and liquid type can move easily ?

Description : Through which molecules of both solvent and liquid type can move easily ?

Last Answer : Molecules of both solvent and liquid type can move easily through cell wall.

What is a solution A. a solid dissolved in a gas B. a solute and a solvent C. a liquid dissolved in a gas D. an amalgam of solids, liquids, and gases?

Description : What is a solution A. a solid dissolved in a gas B. a solute and a solvent C. a liquid dissolved in a gas D. an amalgam of solids, liquids, and gases?

Last Answer : B. A solute and a solvent

Which of the listed precautions should be observed before spraying liquid solvent on the insulation of an electric motor? A. Slow the motor down to low speed. B. Disconnect the motor from the power source. C. Secure all ventilation in the area. D. Preheat the insulation to assist in cleaning.

Description : Which of the listed precautions should be observed before spraying liquid solvent on the insulation of an electric motor? A. Slow the motor down to low speed. B. Disconnect the motor from the power source. C. Secure all ventilation in the area. D. Preheat the insulation to assist in cleaning.

Last Answer : Answer: B

The liquid known as universal solvent?

Description : The liquid known as universal solvent?

Last Answer : Water

what is the name given to a semisolid suspension of a material of high molecular mass in a liquid solvent?

Description : what is the name given to a semisolid suspension of a material of high molecular mass in a liquid solvent?

Last Answer : ANSWER: GEL

Pick out the wrong statement. (A) For the manufacture of styrene, the major raw materials are benzene and ethylene (B) One important copolymer of styrene is SBR, which is widely used in the manufacture of automobile tyres (C) Manufacture of phenol by chloroben-zene-eaustic process involves. The chlorination of benzene, causticisation and hydrolysis (D) Phenol manufacture by chlorobenzene-caustic process is competitive even when low cost chlorine is not available

Description : Pick out the wrong statement. (A) For the manufacture of styrene, the major raw materials are benzene and ethylene (B) One important copolymer of styrene is SBR, which is widely ... D) Phenol manufacture by chlorobenzene-caustic process is competitive even when low cost chlorine is not available

Last Answer : (D) Phenol manufacture by chlorobenzene-caustic process is competitive even when low cost chlorine is not available

In sweetening process, solutizer agent used with caustic alkali is (A) Potassium isobutyrate(B) Sodium plumbite(C) Methanol(D) Phenol

Description : In sweetening process, solutizer agent used with caustic alkali is (A) Potassium isobutyrate (B) Sodium plumbite (C) Methanol (D) Phenol

Last Answer : (A) Potassium isobutyrate

Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Description : Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C

Last Answer : (A) 7 kgf/cm2 and 70 °C